Harman-Kardon AVR 430 owner manual Multi Input

Page 39

MULTI ON. Press the Set Button q again to activate the setting. Note that this method may be used to turn the Multiroom system on or off even when the AVR is in the Standby mode in the main listening room.

IMPORTANT NOTE: When an A-BUS module is con- nected, the AVR’s Multiroom system must be turned on before the A-BUS module is able to communicate with the AVR. Once turned on using the instructions in the preceding paragraph, the Multiroom system must remain on in order for the A-BUS module to operate. When the unit is in the Standby mode, but ready for Multiroom or A-BUS operation, the lighting around the Standby/On Switch 1 remains blue and a MULTI ON message appears in the Lower Display Line $, even though the unit is “off” in the main listening room.

When the Multiroom system is turned on, the input selected using the Multiroom menu will be fed to the Multiroom Audio Outputs j on the rear panel as well as the A-BUS Connector ∞. The volume will be as set in the previous selection, although it may also be adjusted using an optional IR sensor and the Zone II remote in the remote location, or the A-BUS keypad, or on the optional audio power amplifier connected to the Multiroom Audio Outputs j.

Although changes to the input source or remote room volume will normally be made using an IR sensor in the remote room that is connected to the AVR, it is also possible to change those settings from the main listening room. This is useful for situations where some or all of the remote rooms do not have an IR sensor, or to take control over the remote room without actu- ally being in that room.

In addition to using the MULTIROOM menu, as shown on the previous page, you may change the source or volume in the remote zone using the remote. Press the Multiroom Button ` on the remote, and when the MULTI ON/OFF mes- sage appears in the on-screen display and the Lower Display Line $, press the Set Button q and then press the ⁄/¤ Navigation Button o to toggle past that message to MULTI LEVEL or

MULTI INPUT.

MULTIROOM OPERATION

To change the remote room’s input source, when MULTI INPUT appears, press the Set Button q, and then press the ⁄/¤ Navigation Button

ountil the desired input appears in the on-screen display and in the Lower Display Line $. Remember that only analog or PCM input sources may be selected for use with the Multiroom system. Dolby Digital or DTS sources are not available to the Multiroom system.

To change the remote room’s volume, when MULTI LEVEL appears, press the Set Button q, and press the ⁄/¤ Navigation Button o to change the volume setting. Note that this volume adjustment controls the level for the output to the Multiroom Audio Outputs j and for any speakers connected to the Surround Back/Multiroom Speaker Outputs ‚ when the Surround Back amplifier channels are configured for Multiroom use, as shown on page 36. This adjustment does NOT change the volume level for any room where an A- BUS module is used, as that setting is only adjustable using the A-BUS module’s volume control or built-in IR sensor.

Once the Multiroom system is turned on, it will remain on even if the AVR 430 is placed in the Standby mode in the main room by pressing the Power Off Button å or the Main Power Switch A on the front panel.

The Multiroom system will remain on even if the unit is turned off in the main room. In that event, although front-panel indicators and the accent lighting around the volume control will turn off, a MULTI ON message will remain in the Lower Display Line $ and the lighting around the Standby/On switch will remain blue when the unit is in the Standby mode in the main room to remind you that power is still applied to the unit, and that it is being used for Multiroom operation elsewhere in the house. Remember that if you turn the unit completely off by pressing the Main Power Switch A, the feed to the second zone will also be turned off.

When the AVR 430 is turned off in the main room, the Multiroom system may be turned on at any time by pressing the Multiroom Button `, or any of the Selector Buttons ∫ç∂ in the remote room.

MULTIROOM OPERATION 39

Page 38 Page 40
Image 39
Page 38 Page 40
Contents AUDIO/VIDEO Receiver AVRAVR 430 AUDIO/VIDEO Receiver Table of ContentsModèle pour les Canadien Description and FeaturesIntroduction Thank You for Choosing Harman KardonImportant Safety Information Safety InformationFRONT-PANEL Controls To choose from the various mode optionsFRONT-PANEL Controls BC D E F G H I H J K L REAR-PANEL Connections See page 38 for more information on A-BUS Connect the output of the sensor to this jack Plug provided or connect any device to the jack Main Remote Control FunctionsProgram Button SPL Select Button EzSet Microphone Sensor LensMain Remote Control Functions Main Remote Control Functions Main Remote Control Functions Zone II Remote Control Functions Your area Installation and ConnectionsSystem Installation Audio Equipment ConnectionsSystem and Power Connections RS-232 Connections AC Power ConnectionsSpeaker Selection and Placement System ConfigurationSpeaker Placement System SetupFull OSD Time OUT Input SetupMaking Configuration Adjustments Setting the System Configuration MemoryYou to remember which source is being selected Audio SetupTo return to the Master Menu Surround SetupSpeaker Setup Subwoofer Delay Settings To bring up the Master MENU, pressMeasurement units is made, press the ⁄/¤ To change one of the individual speaker positions Output Level AdjustmentUsing EzSet Navigation Button o to return the cursor to the FL positionTo the screen Manual Output Level AdjustmentTo return to normal operation of the AVR Additional Input AdjustmentsSource Selection Volume and Tone ControlOperation Basic OperationSurround Mode Selection Digital Audio PlaybackDTS DH2 Surround Mode ChartMode Features DH1To the AVR PCM Playback Speaker/Channel IndicatorsDigital Bitstream and Surround Mode Indications Selecting a Digital SourceImportant Notes on Digital Playback Tuner OperationRecalling Preset Stations Output Level Trim AdjustmentPreset Tuning Preset number will appear in the Upper Display Line #Memory Backup Menu system Dim FunctionMents to make, press the OSD Button Advanced Features Turn-On Volume LevelDisplay Brightness System Semi-OSD SettingsFull-OSD Time-Out Adjustment Make, press the OSD Button to exit the menu systemMultiroom Setup Multiroom OperationMultiroom Operation Multi Input Configuring the Remote Preprogrammed Code EntryRemote’s Main Menu message Learning Commands Automatic Code EntryLearn appears on the bottom line of the LCD Changing Devices Lower line of the display and then press the Set Button q Macro. The choices are the Power On ButtonRemember that when you want to change devices Macro ProgrammingRead a Macro Power On VID 2/TV VID 3/Cable AVR Logic 7 hProgrammed e.g., the Power On Button 1 or Erasing a MacroPunch-Through Configuration Volume Punch-ThroughChannel Punch-Through When the red light under the Set Button q appears EzSet ConfigurationNumeric Keys RenamingPages 27 Renaming a DeviceResetting the Remote Renaming Individual KeysAt this point you have two options Additional Notes on Configuring and Operating the Remote Amplifier is in protection mode Troubleshooting GuideProcessor Reset Symptom Cause SolutionNtsc AVR 430 Technical Specifications
Related manuals
Manual 54 pages 39.19 Kb

AVR 430 specifications

The Harman-Kardon AVR 430 is a versatile and powerful audio-video receiver that has made a significant mark in the world of home entertainment. Designed for audiophiles and casual listeners alike, the AVR 430 combines advanced technology with user-friendly features, making it an excellent choice for anyone looking to elevate their home theater experience.

One of the standout features of the AVR 430 is its multi-channel audio processing capability. It supports Dolby Digital and DTS surround sound formats, providing immersive audio that allows users to experience movies, music, and games in a whole new way. This receiver is equipped with 5.1 channel amplification, delivering a robust output of up to 70 watts per channel, ensuring that even the most demanding audio tracks come through with clarity and impact.

In terms of connectivity, the AVR 430 offers a range of input options. It includes multiple HDMI inputs that support high-definition video and audio, making it easy to connect modern devices such as Blu-ray players, gaming consoles, and streaming devices. It also features optical, coaxial, and analog inputs, providing compatibility with a variety of audio sources. Furthermore, the inclusion of a dedicated subwoofer output allows users to enhance their system with a powerful subwoofer for deeper bass response.

The AVR 430 is designed with user convenience in mind. It features an intuitive on-screen display that simplifies setup and navigation through various input sources and audio settings. The remote control is ergonomically designed and includes dedicated buttons for quick access to frequently used functions. One noteworthy technology embedded in this receiver is the proprietary Harman Kardon Logic 7 processing, which creates a wider soundstage and more realistic surround sound from stereo sources.

Additionally, the AVR 430 is built with high-quality components that ensure durability and longevity. Its sleek and stylish design allows it to seamlessly integrate into any home entertainment environment. The receiver is also known for its ability to maintain high audio fidelity, thanks to its high-current amplifier design and advanced digital circuitry.

In summary, the Harman-Kardon AVR 430 is an outstanding audio-video receiver that caters to both audiophiles and casual users. Its combination of powerful amplification, extensive connectivity options, intuitive controls, and high-quality sound processing technologies make it a top choice for anyone looking to upgrade their home theater system. Whether enjoying a blockbuster film or listening to favorite music tracks, the AVR 430 delivers an impressive audio experience that is sure to impress.
Top Page Image Contents