Harman-Kardon AVR 5000 owner manual Important Note for the Use SCART-Cinch Adapters

Page 17

Installation and Connections

Figure 1: SCART/Cinch-Adapter for playback; signal flow:

SCART Cinch

Figure 2: SCART/Cinch-Adapter for record and playback; signal flow:

SCART Cinch

Figure 3: Cinch/SCART-Adapter for playback; signal flow:

Cinch SCART

Black

Yellow

Red

Black

Red

Blue1

Yellow

Green1

White

Black

Yellow

Red

Important Note for the Use of

SCART-Cinch Adapters:

When video sources are connected to the TV directly with a SCART cable, specific control sig- nals apart from Audio/Video signals will be fed to the TV. These specific signals are: With all video sources, the signal for automatic input selection that switches the TV automatically to the appropriate input as soon as the video source is started. And with DVD players, the sig- nals automatically turning the TV to 16:9 format (with switchable 4:3 TVs) and turning the RGB video decoder of the TV on or off, depending on the DVD player´s setting. With any adapter cable, these control signals will be lost and the appro- priate setting of the TV must be made manually.

Note for RGB signal with SCART:

If you use a unit providing RGB signals on a SCART output (as e.g. most DVD players do) and you want to use that RGB signal, this SCART

Figure 4:

SCART/S-Video Adapter

for playback;

signal flow:

SCART Cinch

Figure 5:

SCART/S-Video Adapter

for record and playback;

signal flow:

SCART Cinch

Figure 6:

SCART/S-Video Adapter

for playback;

signal flow:

Cinch SCART

Red

Black

S-Video In

Black

Red

Blue1

Yellow

S-Video In

S-Video Out

Red

Black

S-Video Out

1Also other colours possible, e.g. brown and grey.

output must be connected directly to your TV. Although the AVR 5000 RDS can switch three- way video signals (like component signals Y/Pb/Pr), most TVs need separate sync signals for RGB (also with SCART) that cannot be switched and provided by the AVR 5000.

RGB signals can be pathed through

the AVR5000 only when no separate sync signal is needed (see 4th ”Video Connection Note” on page 16).

INSTALLATION AND CONNECTIONS 17

Image 17
Contents AVR 5000 Audio/ Video Receiver Declaration of Conformity Table of ContentsFront-Panel Analog A/V Inputs switch- able to Outputs Description and FeaturesIntroduction Output Levels for OptimumUnpacking Safety InformationImportant Safety Information Front Panel Controls Preset Stations Selector ÓVolume ControlFront Panel Controls See Front Panel Information Display Dolby 3 Stereo Indicator Preset IndicatorFront Panel Information Display Front Panel Information Display FM Antenna Multiroom IR Input Rear Panel ConnectionsCD Inputs DVD Video Inputs Rear Panel ConnectionsDigital recorder such as a CD-R or MiniDisc recorder Unswitched OutletMain Remote Control Functions Settings after the Delay button has been pressed Direct Input Zone II Remote Control Functions Video Equipment Connections Installation and ConnectionsAudio Equipment Connections Video Connection Notes Scart A/V ConnectionsVideo Video In/Out jacks, if it´s a recording VCR Important Note for Adapter CablesImportant Note for the Use SCART-Cinch Adapters RGB signals can be pathed throughSystem and Power Connections Speaker Placement System ConfigurationSystem Configuration Speaker SelectionSwitched AC outlet Settings to be Made With Each Input UsedUsing the On-Screen Display Selecting the On-Screen displaySurround Setup Input SetupSurround Speaker SetupDelay Settings Adjustments for Other InputsOutput Level Adjustment Night Mode SettingsProper Outputs Using EzSetPress and hold the SPL Indicator Select Will change color to indicate the level On the remote only, not the main vol- ume controlsTo turn the test tone off and return to Master MenuOperation Controls and Use of HeadphonesBasic Operation Source SelectionSurround Mode Chart Digital Audio Playback Surround Mode SelectionDolby Digital Rear panel Or front panel #%Selecting a Digital Source MP3 Audio PlaybackRear panel Digital Inputs Tape Recording Record modeAudio Outputs Or 2 OutputsSelect to turn the sensor and indicator off Output Level Trim AdjustmentPress the OSD button Lto view the Master Menu Figure To raise or lower the output levelTuner Operation Memory BackupChannel Direct Input RDS Operation RDS TuningRDS Display Options Program Search PTYOperation Display Brightness Advanced FeaturesTurn On Volume Level Advanced Features Semi-OSD SettingsFull-OSD Time Out Adjustment Multiroom Setup InstallationMultiroom Operation Multiroom OperationProgramming the Remote with Codes Time. When the Program/SPL IndicatorDirect Code Entry Auto-Search MethodLearning Codes from a Remote Code ReadoutVID1/VCR VID2/TV Erasing Learned CodesProgramming the Remote Erasing Macro CommandsMacro Programming Press any Input Selector 456and also the Learn buttonProgrammed Device Functions Volume Punch-ThroughRemote With Other Devices 4and the Mute buttonSelector button Resetting the Remote MemoryChannel Control Punch-Through SPL Function ListAVR DVD Function ListSetup Code Table TV Hifivox HanseaticHitachi ImperialRediffusion RbmukRediffusionuk RedifusionSetup Code Table VCR Graetzitt GbcukHARMAN/KARDON ITT/NOKIARealistic RCASansui SunstarSetup Code Table CD Code Number 3digit List Setup Code Table CBLSetup Code Table SAT Code Number 3 Digit List Setup Code Table DVDProcessor Reset Troubleshooting GuideAmplifier is in protection mode Motors or other electrical appliancesTechnical Specifications Harman Consumer International