Euro-Pro SC717XH owner manual Assembly and Using the Steamer, Filling and Refilling the Steamer

Operating Instructions

Operating Instructions

Caution: Always ensure the unit is unplugged from the wall receptacle prior to filling or re-filling the water tank.

Important: Disconnect steam cleaner from wall outlet before refilling. It is time to refill your steam cleaner when there is no more steam coming out of the

7.Screw safety cap back on the appliance and plug appliance back into wall outlet. Steam will start to be produced as before.

Assembly and Using the Steamer

1.Before filling the steam cleaner, make sure that the unit is NOT plugged in. Also, slide the safety trigger lock to the right to lock it. (Fig. 1) To unlock this safety feature, slide the trigger safety lock to the left. (Fig. 2)

Locked	Unlocked
Fig. 1
	Fig. 2

2.Simultaneously press down on the safety cap and turn it counter- clockwise until removed.

3.Place funnel in the tank and add water. DO NOT overfill.

Maximum filling capacity is 300 mL (10 oz.) Replace the safety cap by turning it clockwise until it has tightened. Attach desired accessory attachment.

Note: Heating time is approximately 4 to 5 minutes. Filling the boiler with hot water will shorten heat up time.

4.Plug the unit into a standard 120 volt wall receptacle. The heating light will then light up.

5.Allow approximately 4 to 5 minutes for water vapor to reach its working temperature and pressure.

6.At the start, some water may come out of the nozzle (this is normal).

7.Grasp the handle firmly with one hand and slide the trigger safety lock to the left to unlock it.

8.Using your thumb, press down on the trigger button to release the steam (“ON” position). Turn the variable steam adjustment in a clockwise or counterclockwise direction to change the amount of steam released. To stop steam from being released, let go of the trigger button (“OFF" position).

Important Note: On the top of the trigger button, there is a slide that can be used to lock the trigger in the “ON” position. To engage it, depress the trigger button with your thumb and then slide your thumb forward. (Fig. 3) To release the lock and turn off the steam, press down on the slide and pull it back, then release the pressure on the trigger.

To avoid loss of steam while the unit is heating, be sure that the steam trigger is not depressed or locked in the “ON” position prior to plugging the unit in.

Locked in the “ON” position

Fig. 3

9.When finished using the steam cleaner, unplug and allow to cool. Follow the instructions in the “Maintenance & Cleaning Instructions” section.

Warning: DO NOT aim steam at any live electrical components or devices, such as electrical outlets.

nozzle.

Warning: Because the water tank is pressurized, use caution when opening to refill. Always unplug the unit and let the unit cool for 15 minutes before opening the safety cap. Depress the trigger button while you unscrew the safety cap counter-clockwise.

Caution: When refilling the appliance while it is still hot, the first drops of water might squirt back. Use caution when opening the safety cap.

Filling and Refilling the Steamer

1.Disconnect electrical power cord from wall outlet.

2.Press down on the trigger button until all pressure has been released.

3.Wait for approximately 15 minutes before carefully unscrewing the safety cap.

4.Turn slowly a half turn counter- clock wise and wait for the hissing noise created by residual steam to stop.

5.Unscrew the safety cap in the counter-clock wise direction until it is completely unscrewed and allow it to cool.

6.Slowly pour water into the boiler using the measuring cup and the funnel. (Fig. 4)

Funnel

Fig. 4

Warning: This appliance is under pressure. After every use, press trigger button until all pressure has been released before removing safety cap.

Important: DO NOT OVERFILL.

Maximum filling capacity is 300 ml. (10 oz.).

Concentrator Nozzle

To attach the concentrator nozzle:

•Align the raised arrow on the larger end of the concentrator nozzle with the single white line on the ring of the snout. (Fig. 5 & 6)

•Push the concentrator onto the nozzle until it stops against the appliance.

•To lock the concentrator nozzle in place, turn it 90 degrees clockwise so that the raised arrow mark aligns with the two white lines on the ring of the snout. (Fig. 6)

Larger End of the

Concentrator Nozzle

	The ring of
Fig. 5
	the Snout

Align the

raised arrow mark and the single white line.

Fig. 6

5

6