OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS cont.
How To Assemble & Use
IMPORTANT: Always insure that the unit is “UNPLUGGED” from the wall receptacle prior to initial filling or
Step 1: Before filling the steam cleaner, make sure that the unit is NOT plugged in.
Step 2: Press locking trigger to ensure all internal pressure is released.
Step 3: Turn Safety Cap counter clockwise until removed.
Step 4: Release locking trigger.
Step 5: Add 28 fl. oz (800 cc) of water using the filling flask provided. Do not overfill. Replace Safety Cap by turning clockwise - press down firmly to tighten. Heating time is approximately 6 minutes. Filling the boiler with hot water will shorten heat up time.
Step 6: Plug the unit into a standard 120 volt grounded wall receptacle. The power “On” light (Red) will light up.
Step 7: Allow approximately 6 minutes for water vapor to reach its working temperature and pressure. When unit is ready for use the red light will change to Green.
Step 8: At the start, some water will come out from the nozzle. This is normal.
NOTE: Disconnect steam cleaner from wall outlet before refilling. It is time to refill your steam cleaner when there is no more steam coming out of the nozzle. Because the water tank is pressurized, use caution when opening to refill. Depress the trigger button while you unscrew the safety cap counterclockwise. Always let unit cool for 5 minutes before refilling the unit with water.
CAUTION: When refilling the appliance while it is still hot, the first drops of water might bubble up.
5
Using the Locking Trigger Button
The steam cleaner has a locking trigger button. The trigger will lock when you have pushed it in all the way. To unlock the steam trigger, just press the locking trigger button in and the steam trigger will pop up, stopping the flow of steam.
Refilling With Water
Step 1: Disconnect electrical power cord from wall outlet.
Step 2: Press trigger button until all pressure has been released.
Step 3: Allow the unit to cool for approximately 5 minutes before refilling with water.
Carefully unscrew safety cap. Step 4: Slowly pour water using the
filling flask into the boiler.DO NOT Fill Under a faucet, use the filling flask provided. DO NOT OVERFILL. Always leave approximately 2 1/2 inches between the top of the unit and the water level.
Step 5: Release the locking trigger.
Step 6: Screw safety cap back on the appliance and plug appliance back into wall outlet. Steam will start to be produced as before.
WARNING: This appliance is under pressure. After every use, press trigger button until all pressure has been released before removing safety cap. Allow unit to cool for five (5) minutes before refilling.
ATTACHMENTS
Angle Concentrator/Brush Adapter
To attach the angle concentrator/brush adapter to the hose, hold the hold grip in one hand and insert the angle concentrator/brush adapter into the nozzle end of the hand grip. Make sure that it locks in place. (See below.)
Using Accessories
To use the nylon detail brushes, attach the nylon bristle brush to the end of the angle concentrator/brush adapter. (See below.)
Window Squeegee
CAUTION: When cleaning windows, always avoid any sudden changes in temperature to prevent glass breakage or cracks.
Please note that the window squeegee can only be used with the
hose. To attach the window squeegee to the hose, push it in until the squeegee locking button clicks in place on the hose.
Apply steam abundantly,
rub with the soft spongy end, then remove excess water and dirt with the glass wiping edge.
This attachment is very useful for cleaning large windows, plastic material, ceramic, tiled or marble surfaces.
Using the Steam Cleaner with Floor Brush
Step 1: Connect one of the extension tubes to the hand grip on the flexible steam hose. To attach the extension tubes one onto the other or
onto the hand grip, press the locking button ensuring that it fits into the hole. (See illustrations.) To disconnect, repeat the operation by pressing the locking button and pulling the two sections apart.
Extension Tubes
NOTE: Fit floor brush with the floor brush angle adapter
on to the extension tube.
Step 2: If the floor brush angle adapter is not attached to the floor brush, hold the brush with its bristles up in your left hand. With the floor brush angle adapter pointing downward, insert it into the hole in the back of the brush, then turn the floor brush angle adapter 180°.
Step 3: Insert the electrical power cord into the wall outlet. Heating time is approximately 6 minutes with cold water. Filling the steam generator with hot water
6will shorten heat up time.