SECTION 3
CARE OF YOUR WATER SOFTENER
D. CHECKLIST ... TO HELP YOU SAVE MONEY
,I \RXU ZDWHU VRIWHQHU IDLOV WR ZRUN PDNH WKH IROORZLQJ HDV\ FKHFNV 2IWHQ \RX ZLOO ILQG ZKDW·V ZURQJ \RXU VHOI DQG \RX ZRQ·W KDYH WR FDOO DQG ZDLW IRU VHUYLFH ,I \RX GR QRW ILQG DQ\WKLQJ ZURQJ ZKLOH PDNLQJ WKH FKHFNV DQG \RXU VRIWHQHU VWLOO GRHV QRW ZRUN FDOO .HQPRUH :DWHU /LQH DW
1RWH
$OVR UHDG (5525 &2'( SDJH
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
PROBLEM | CAUSE | CORRECTION |
|
|
|
1R VRIW ZDWHU | No salt (or salt bridged) in the storage tank | Refill with salt, or break the salt bridge (page |
|
| |
|
| NOW) button and hold for 3 seconds to start a |
|
| regeneration (see page |
| Transfomer unplugged at the wall outlet, | Check for loss of power due to any of these |
| or power cable leads loose, fuse blown, | and correct. With the power back on, look at |
| circuit breaker popped, or circuit switched | the time display and read PROGRAM |
| off. | MEMORY, page |
|
|
|
| Manual bypass valve(s) in bypass position | Look at FIG.14 on page |
|
| a single valve to service. In a |
|
| open the inlet and outlet valves, and be sure to |
|
| fully close the bypass valve. |
|
|
|
| Dirty, plugged or damaged nozzle & | Take apart and clean or replace damaged |
| venturi | parts (see page |
| Valve drain hose plugged | The drain hose must not have kinks, sharp |
|
| bends, or be raised too high above the |
|
| softener (see page 16 in your LQVWDOODWLRQ |
|
| PDQXDO). |
:DWHU KDUG VRPHWLPHV | Hardness number setting too low | Press and release the SELECT button until |
|
| HARDNESS shows in the display. Read the |
|
| hardness number in the display and be sure |
|
| the same grains per gallon number is shown |
|
| on your water analysis report. See page |
|
| reset. Press and release the SELECT button |
|
| until the present time shows in the display. |
|
| Incorrect SR code selected. See above. |
|
|
|
| Using hot water when softener is | Avoid using hot water during this time because |
| regenerating | the water heater refills with hard water (see |
|
| Automatic Bypass, page |
|
|
|
| Increase in the grains of hardness in your | Ask your Sears retail store for a new water |
| water supply | analysis. Then make a new hardness number |
|
| setting (page |
|
|
|
%ULQH WDQN IORRGHG | Restricted drain line | Check for kinks, bends or obstructions (see |
|
| page 16 in your LQVWDOODWLRQ PDQXDO). |
| Plugged or dirty nozzle & venturi | Take apart and clean or replace damaged |
|
| parts (see page |
| Check for scratches or grooves, replace if | |
|
| needed. |
3UREOHPV 4XHVWLRQV" &DOO .HQPRUH :DWHU /LQH