Electronic Faucet Installation

ELECTRONIC FAUCET INSTALLATION

Be sure there is room underneath the sink to make the needed connections. Select one of the following places to install the faucet:

—IN an existing sink spray attachment or soap dispenser hole

—IN a hole to be drilled in the sink top

—IN a hole to be drilled in the countertop, next to the sink

NOTE: Looking at Fig. 3D, be sure the faucet base will fit flat against the surface at the selected location so the gasket will seal. The base may have to be angled sideways or diagonally.

1.	If drilling is needed, make a 1-1⁄4″ dia. hole. Be sure to use the
	proper procedure for drilling porcelain or stainless steel. Special
	drill bits may be needed.
2.	Looking at Fig. 3A, insert a screw into the NON-SLOTTED base
	mounting hole. Turn a flat nut a few turns onto the screw.

Fig. 3A.	Fig. 3B.	Nut (2)
Fig. 3A.	Fig. 3B.	TOP VIEW
	Screw (2)	Screw (2)
	Faucet
	base
	Faucet
	base
	Gasket	″
Nut (2)		1-1/4 dia. mounting
Nut (2)		hole in sink or

countertop

3.	Position the base gasket over the mounting hole. Set the base on
	the gasket, routing the leadwire through the mounting hole.
	Holding the flat nut under the sink with one finger, tighten the
	screw until just snug.
4.	Turn the remaining flat nut a few turns onto the other screw.
	Position the screw in the slotted base mounting hole and tighten
	until snug. Make sure the gasket position is properly aligned and
	carefully tighten both screws until the base is held firmly in place.
	Do not overtighten and break the base.
5.	Assemble the top faucet base and hex nut onto the faucet stud
	(Fig. 3C). Tighten the nut until snug.
6.	Insert washer into tubing adapter. Securely tighten to faucet stud.
7.	Put a few wraps of Teflon Tape* on the end of the faucet stud.
	Using the plastic washer, turn the tubing adapter onto the faucet
	stud and tighten securely.

Fig. 3C.

Spout

Lever

Faucet

Faucet stud

Top faucet base

ASSEMBLED

8.	Feed the length of 3⁄8″ OD tubing from the bottom, up through
	the faucet base. Connect to the tubing adapter as shown
	in Fig. 3C., tightening the compression nut securely.
9.	Remove the short shipping tube and insert the spout into the
	faucet body.
10.	Lower the faucet assembly and lock into place on the faucet base.

Fig. 3D.

Hex nut

Washer

Tubing

adapter

Compression

nut

Compression

nut

3/8″ tubing, (run to Filter 2 outlet)

Base leadwire connector

(to battery pack)

Faucet base

*Teflon Tape is a Registered Trademark of Dupont.

GNUL30Z specifications

The GE GNUL30Z is a cutting-edge refrigerator designed to meet the demands of modern households. Combining advanced technology with sleek aesthetics, this refrigerator stands out as a reliable and efficient appliance for any kitchen.

One of the main features of the GE GNUL30Z is its spacious interior, which provides ample storage for groceries and perishables. The refrigerator boasts a capacity of approximately 30 cubic feet, making it ideal for families or households that often entertain guests. The flexible shelving system can be easily adjusted to accommodate items of varying sizes, from tall bottles to small containers.

In terms of technology, the GE GNUL30Z is equipped with the latest cooling innovations. The advanced cooling system ensures that temperatures remain consistent throughout the refrigerator, preventing spoilage and extending the freshness of stored food. Additionally, the refrigerator features an automatic defrost function, which eliminates the need for manual defrosting and helps maintain optimal performance.

Energy efficiency is another highlight of the GE GNUL30Z. With an Energy Star certification, this model has been designed to consume less energy than traditional refrigerators, making it an eco-friendly choice for conscientious consumers. This efficiency not only helps reduce electricity bills but also minimizes the overall carbon footprint of the household.

Another noteworthy characteristic of the GE GNUL30Z is its integrated smart technology. This refrigerator can connect to your home Wi-Fi network, allowing users to monitor and control settings remotely through a smartphone app. Notifications about door open alerts, temperature adjustments, and filter replacement reminders enhance the user experience and convenience.

The exterior of the GE GNUL30Z is equally impressive, featuring a sleek stainless-steel finish that adds a touch of elegance to any kitchen decor. The fingerprint-resistant coating is an added bonus, making it easy to maintain a clean and polished look despite regular use.

Overall, the GE GNUL30Z embodies the perfect blend of functionality, advanced technology, and style. Its spacious design, energy efficiency, smart features, and attractive appearance make it a top choice for those seeking a reliable refrigerator that can meet the demands of contemporary living. Whether for everyday use or special occasions, this model proves to be a valuable addition to any home.

ELECTRONIC FAUCET INSTALLATION

(Fig. 3C). Tighten the nut until snug.

GNUL30Z specifications