Brother Brother CP-6500 Thread tension, Correct tension, Upper tension is too tight

Page 43

——————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

Thread tension

The thread tension will affect the quality of your stitches. You may need to adjust it when you change fabric or thread.

Memo

●We recommend that you do a test sample on scrap of a fabric before you start to sew.

■Correct tension

Correct tension is important as too much or too little tension will weaken your seams or cause puckers on your fabric.

1

 

a Wrong side

2

b Surface

 

c Upper thread

 

d Lower thread

3

4

■Upper tension is too tight

Loops will appear on the surface of the fabric.

Note

●If the bobbin thread was incorrectly threaded, the upper thread may be too tight. In this case, refer to “Lower threading” (page 19) and rethread the bobbin thread.

1

a Wrong side

Memo

●When you finish sewing, remove the bobbin cover and then make sure that the thread is shown as below. If the thread is not shown as below, the thread is not inserted through the tension-adjusting spring of the bobbin case correctly. Reinsert the thread correctly. For details, refer to page 19, 20.

2

■Upper tension is too loose

Loops appear on the wrong side of the fabric.

Note

●If the upper thread was incorrectly threaded, the upper thread may be too loose. In this case, refer to “Upper threading” (page 22) and rethread the upper thread.

 

 

b Surface

2

 

c Upper thread

 

 

d Lower thread

 

 

e Loops appear on

3

5

surface of fabric

 

4

Solution

Reduce the tension by turning the upper

15

2

3

4

aWrong side

bSurface

cUpper thread

dLower thread

eLoops appear on wrong side of fabric

tension-control dial to a lower number.

5

4

3

Solution

Increase the tension by turning the upper tension-control dial to a higher number.

5

4

3

41

Page 42 Page 44
Image 43
Page 42 Page 44
Contents Sewing Basics Utility Stitches Page Important Safety Instructions For a longer service life For Users in the UK, EIRE, Malta Cyprus only Contents Utility Stitches Included accessories AccessoriesAbout zigzag foot J Accessory compartment Optional accessoriesMain parts Names of Machine Parts and Their FunctionsOperation buttons Needle and presser foot sectionButtons provided on some models Spool pin Operation panelBPushplace.the spool pin down until it locks into Shown.1Power supply precautions Using Your Sewing MachinePower supply Side of stitch selection key Foot controllerChanging the needle stop position Aright to select the desired sewing speedWinding the bobbin Threading the MachineBRemove the spool cap DSlide the spool cap onto the spool pin KTrim the excess thread above the bobbin Make sure that the thread passes under the pretension diskFor models equipped with the fast bobbin winding system Thread is cut to a suitable length Actual size 11.5mm 7/16 inch This model Lower threadingFor models equipped with the quick-set bobbin Slit Cutter Cut the thread with the cutter Upper threading GSlide the spool cap onto the spool pin Remove the spool capThread take-up lever Needle bar thread guide Catch the thread on the hook as shown below DFully lower the needle threader leverLightly hold the end of the upper thread Drawing up the lower threadBobbin cover should still be removed Replacing the Needle Needle precautionsNeedle types and their uses Replacing the needle Checking the needleCLower the presser foot lever Install the twin needle in the same wayFor details, refer to steps a through l of Upper threading Installthread.the thread spool and thread the upperSewing with the twin needle Thread the upper thread for the left needleTurn on the sewing machine Select a stitch For details, refer to step a through l of Upper threadingHAttach zigzag foot J Models equipped with a needle threaderMark on the wheel points up. With models Replacing the Presser FootReplacing the presser foot Replace the presser foot as described belowRemove the presser foot Removing the presser foot holderFor details, refer to Replacing the presser foot Page Follow the basic procedures below to sew General sewing procedureSewing On the left changes the digit on the left DIfwidth.necessary, adjust the stitch lengthSelecting stitching Press the + or side of to increase orRight of in the LCD Adjusting the stitch length and widthOn the wheel points up. With models equipped Starting to sewBRaise the presser foot lever Sewing reinforcement stitches Raise the presser foot leverEach other Upper tension is too loose Thread tensionCorrect tension Upper tension is too tightSewing curves Useful Sewing TipsTrial sewing Changing the sewing directionPresser foot remains level, allowing the fabric to be fed Sewing hook-and-loop FastenerSlide the flat bed attachment to the left to release it Sewing thin fabricsSewing stretch fabrics Stitching cylindrical piecesCSew with the edge of the fabric Using zigzag footOvercasting Stitches Attach zigzag foot J Select stitch , orAttach overcasting foot G Select stitch or Using overcasting footFor details, refer to Starting to sew When sewing is finished, cut the threadBasic Stitching Basic stitchingReverse the skirt or pants Blind HEM StitchingFold back the fabric inside along the basting Thick fabric Normal fabric Stitch widthIf the needle does not catch the hem fold Buttonholes can be sewn and buttons can be sewn on Buttonhole SewingAuto Rfc. Automatic Reinforcement **Rfc. Reinforcement Size of the buttonhole is set Raiseposition.the buttonhole lever to its original Once sewing is completed,Trim off any excess of the gimp thread Sewing buttonholes on stretch fabricsWith stitch Select stitch Button sewingDPlacethe fabric.a button between the presser foot ESelect a stitchNormally, the feed dog position lever is Positioned at After sewing for about 10 seconds at lowRev. Reverse Do not use reverse stitching Zipper InsertionRefer to Basic stitching on Sew the stitching in order, from a to c FSelect stitchBAttach zigzag foot J CSelect stitch Sewing Stretch Fabrics and Elastic TapeStretch stitching Elastic attachingUtility Stitches Piecing APPLIQUÉ, Patchwork and Quilt StitchingRemove the basting, if necessary AppliquésPatchwork crazy quilt stitching PiecingSewing QuiltingFor a seam allowance on the left side DSelect stitchARemoveholder. the presser foot and the presser foot Using the optional quilting guideFree-motion quilting † Walking foot † Presser foot holderSlide the feed dog position lever, located at Attach zigzag foot J Select stitch Start sewing Reinforcement StitchingTriple stretch stitching Bar tack stitchingPullpossible.down the buttonhole lever as far as Once sewing is completed,Decorative Stitching Fagoting CSew parallel stitching at intervals of 10 mm 3/8 inch Scallop stitchingSmocking DTrim along the stitchesUnfold the fabric, and then iron the tucks down to one side Shell tuck stitchingJoining Fold the fabric along the bias BAttach zigzag foot JHeirloom stitching Utility stitches Stitch SettingsPattern No Decorative Stitch Buttonhole Bar tack For decoration, etc For decoration, etc Yes Remove the bobbin case MaintenanceCleaning the machine surface Cleaning the bobbin caseAlign the U and marks Needle plate cover Frequent troubleshooting topics TroubleshootingUpper thread tightened up Cause Incorrect upper threading SymptomFor details, refer to Cleaning the bobbin case on Tangled thread on wrong side of fabricHFeed the upper thread as shown in the illustration below Thread take-up lever Incorrect thread tension DRemoveholder. the presser foot and presser foot Fabric is caught in the machine and cannot be removedIf threads remain in the bobbin case, remove them Be careful not to drop the removed screws in the machine Memo Correctly thread the machine Do not yet install the presser foot and threadChecking machine operations Turn on the machine Select middle needle position stitchList of symptoms Fabric being Sewn with While sewingMachine does Not workOr breaks UpperThread breaks LowerPitched noise While sewing Stitches areSkipped There is a highThread After sewingThread has Tightened upOperation beep for models equipped with the operation beep Error MessagesNumerics Index42 , 45 English 885-V60/V61/V62/V63/V64/V65 XE6528-2012

Brother CP-6500 specifications

The Brother CP-6500 is a versatile and feature-rich sewing and quilting machine that has gained popularity among both amateurs and seasoned enthusiasts. With an array of advanced technologies and user-friendly features, it effectively combines creativity and convenience, making it an ideal choice for various sewing projects.

At the heart of the CP-6500 is its powerful motor that delivers strong and consistent stitch quality across a wide range of fabrics. This machine is capable of sewing both lightweight materials such as silk and heavier fabrics like denim, catering to a diverse collection of sewing needs. The built-in sewing speed control allows users to adjust the speed of the machine, making it easier to tackle intricate or delicate tasks with precision.

One of the standout features of the Brother CP-6500 is its extensive selection of built-in stitches. The machine boasts over 100 stitch options, including utility stitches, decorative stitches, and quilting stitches. This wide variety allows for creative expression and enhances the ability to customize projects to suit individual preferences. The included stitch guide makes it simple to choose the right stitch for each task, ensuring consistent results every time.

Another notable technology integrated into the CP-6500 is the automatic needle threader, which saves time and reduces frustration. This feature seamlessly threads the needle with just the push of a lever, eliminating the hassle of manual threading. Additionally, the top-loading bobbin system is designed for easy access and quick bobbin changes, further streamlining the sewing process.

The CP-6500 is equipped with an LCD screen that provides clear visibility of stitch selection, making it user-friendly even for those new to sewing. The machine also includes adjustable stitch length and width, allowing for further customization to achieve the desired look and feel of the finished product.

With a lightweight design, the Brother CP-6500 is easy to transport, making it suitable for taking to sewing classes or quilting groups. The included hard case provides added protection during travel, ensuring the machine remains in pristine condition.

In summary, the Brother CP-6500 stands out as a capable and efficient sewing machine that combines technology with user-friendly features. Its extensive selection of stitches, automatic needle threader, and adjustable settings make it an excellent choice for anyone looking to enhance their sewing experience, whether for casual projects or serious quilting endeavors.
Top Page Image Contents