Brother LK3-B448E Environmental requirements, Lightning may cause problems with correct operation

Page 3

DANGER

Wait at least 5 minutes after turning off the power switch and disconnecting the power cord from the wall outlet before opening the face plate of the control box. Touching areas where high voltages are present can result in severe injury.

CAUTION

Environmental requirements

Use the sewing machine in an area which is free from sources of strong electrical noise such as high- frequency welders.

Sources of strong electrical noise may cause problems with correct operation.

Any fluctuations in the power supply voltage should be within ± 10% of the rated voltage for the machine.

Voltage fluctuations which are greater than this may cause problems with correct operation.

The power supply capacity should be greater than the requirements for the sewing machine’s electrical consumption.

Insufficient power supply capacity may cause problems with correct operation.

The ambient temperature should be within the range of 5° C to 35° C during use.

Temperatures which are lower or higher than this may cause problems with correct operation.

The relative humidity should be within the range of 45% to 85% during use, and no dew formation should occur in any devices.

Excessively dry or humid environments and dew for- mation may cause problems with correct operation.

Avoid exposure to direct sunlight during use.

Exposure to direct sunlight may cause problems with correct operation.

In the event of an electrical storm, turn off the power and disconnect the power cord from the wall outlet.

Lightning may cause problems with correct operation.

Installation

Machine installation should only be carried out by a qualified technician.

Contact your Brother dealer or a qualified electrician for any electrical work that may need to be done.

The sewing machine weighs more than 47 kg. The installation should be carried out by two or more people.

Do not connect the power cord until installation is complete, otherwise the machine may operate if the foot switch is pressed by mistake, which could result in injury.

Hold the machine head with both hands when tilting it back or returning it to its original position. Furthmore, after tilring back the machine head, do not push the face plate side or the pulley side from above, as this could cause the machine head to topple over, which may result in personal injury or damage to the machine.

Be sure to connect the ground. If the ground connec- tion is not secure, you run a high risk of receiving a serious electric shock, and problems with correct operation may also occur.

All cords should be secured at least 25 mm away from any moving parts. Furthermore, do not excessively bend the cords or secure them too firmly with staples, otherwise there is the danger that fire or electric shocks could occur.

Install the belt covers to the machine head and motor.

If using a work table which has casters, the casters should be secured in such a way so that they cannot move.

Be sure to wear protective goggles and gloves when handling the lubricating oil and grease, so that they do not get into your eyes or onto your skin, otherwise in- flammation can result.

Furthermore, do not drink the oil or eat the grease under any circumstances, as they can cause vom- iting and diarrhoea.

Keep the oil out of the reach of children.

LK3-B448E MARKII/BA-16

ii

Image 3
Contents LK3-B448E Indications SymbolsEnvironmental requirements Lightning may cause problems with correct operationIii SewingLK3-B448E MARKII/BA-16 Contents Changing functions using the DIP switches Name of each part Name of each partNeedle SpecificationsSpecifications SpecificationsProgram list Specifications Program No Optional parts Installation Power tableInstallation Installing the motor pulley Installing the motorInstalling the control box Installing the cushions Installing the oil panInstalling the head rest Installing the machine headInstalling the liquid cooling tank, optional Installing the vibrating bowlInstalling the control box for vibrating bowl Installing the shooter Installing the button feederP11 Connecting the cordsControl box for vibrating bowl connection Installation Button feeder connectionInstalling the button feeder cover Installation Power switch connectionPower switch connector control box Connecting the ground wire Installing the operation panelInstalling the V-belt Installing the foot switch Installing the belt coverInstalling the spool stand Installing the eye guard Installing the motor coverAdjustment by the accessory spring Lubrication Lubrication pointsLubrication Draining the oil Applying greaseOperation Name and function of each operation panel itemOperation S E TY-SCALE Setting the sewing speed Operating procedureSetting the program number Setting the X-scale and Y-scaleOperating the vibrating bowl Operating the button feederChecking the sewing pattern When checking by operating only the feed mechanismTo ensure safety during use Checking the sewing patternThreading the upper thread Installing the needleCorrect use Selecting the needle and threadWinding the lower thread Replacing the bobbin case and threading the thread Thread tension reference guideLower thread tension Upper thread tension Thread take-up amount Adjusting arm thread guide RSewing SewingBefore starting sewing Maintenance and inspection Maintenance and inspectionCleaning the rotary hook Cleaning the control box air inlet portCleaning the eye guard Wipe the eye guard clean with a soft clothChecking the needle Adjustments AdjustmentsTileing back the machine head Adjusting the needle bar lift amount Adjusting the needle bar heightAdjusting the driver needle guard Adjusting the needle clearanceAdjusting the shuttle race thread guide Adjusting the movable knife Adjusting the thread take-up amountAdjustments Replacing the movable knife and fixed knife Adjusting the button clamp lift amount Adjusting the holding pressure Adjusting the position of the button holderAdjustment Adjusting the button clamp height Adjusting the thread wiper Adjusting the needle up stop positionIf buttons are not fed properly, check the following Adjusting the vibrating bowlAdjustment for excess buttons in the button shooter Button clamp adjustment Button replacementAdjustment Adjustment when the button thickness changes Adjusting the button carrier plateIf button hole arrangements differ Adjustment Adjusting the feeder position adjustment Vertical feed position Adjustment Adjusting the needle locationHorizontal feed position Button hole gapReplacement the V-belt Sewing machine Belt P1 P2 P3 P4 Checking the input sensor and DIP switch inputChecking the input voltage Moving stitch patterns Using the counters Using the countersUsing the bobbin thread counter Using the production counterP1 P2 Using user programsUsing user programs Recording a user programClearing the user programs Using user programs Using a user programRecording a cycle sewing program Using the cycle sewing functionUsing the cycle sewing function Press the P1 switch oClearing a cycle sewing program Using the cycle sewing function Using a cycle sewing programChanging functions using the DIP switches Changing functions using the DIP switchesOperation panel DIP switches Setting the presser modeDIP switches inside the control box P1 P2 P3 P4 Clearing all memory settingsChanging special functions using the memory switches Memory switches 00 0FMemory switches 30 4F Memory switches 20 2FTable of error codes Table of error codesErrors generated when optional equipment is connected Segment LED alphabetPanel display Text display LK3-B448E MARKII/BA-16 Troubleshooting Troubleshooting40,46 Hole of the button Needle drops into15-1, Naeshiro-cho, Mizuho-ku, Nagoya 467-8561, Japan. Phone

LK3-B448E specifications

The Brother LK3-B448E is a versatile and innovative sewing machine designed to meet the needs of both home sewers and professionals alike. This comprehensive machine is especially advantageous for users who want to experiment with intricate designs and achieve high-quality results with ease.

At the core of the LK3-B448E lies its advanced computerized technology, which facilitates a seamless sewing experience. The machine features a user-friendly interface, making it accessible for not just experienced sewists but also beginners. The LCD display provides clear visibility of settings, stitch patterns, and design options, ensuring that users have full control over their projects.

One of the standout features of the LK3-B448E is its extensive library of built-in stitch patterns. With over 100 different stitches to choose from, including decorative, utility, and quilting stitches, users can easily customize their sewing to suit any project. In addition to the built-in stitches, this machine supports the use of embroidery patterns and designs, expanding creative possibilities significantly.

The LK3-B448E also incorporates advanced sewing technologies, such as automatic needle threading and a drop-in bobbin system. These features simplify the setup process, allowing users to spend more time sewing and less time managing technicalities. Furthermore, the machine offers adjustable stitch length and width, enabling personalized settings that cater to various fabric types and sewing tasks.

Another remarkable characteristic of the LK3-B448E is its adjustable presser foot pressure. This allows for better control, whether working with delicate fabrics or thicker materials. The machine’s speed controls help manage sewing speed, providing additional comfort for users as they tackle intricate patterns or detailed designs.

The LK3-B448E also supports USB connectivity, enabling users to transfer new designs and updates effortlessly. This feature ensures that the machine remains relevant with cutting-edge patterns and functionalities, extending its lifespan and usability.

In conclusion, the Brother LK3-B448E combines user-friendly design with advanced technology, offering a comprehensive sewing experience. Its extensive features, coupled with customizable settings, make it an ideal choice for both novice and experienced users looking to enhance their sewing projects. With the LK3-B448E, creating beautiful garments and intricate designs is a straightforward and enjoyable process.