Brother rh-918a manual Installing the needle, Threading the upper thread

Page 35

5. CORRECT USE

5-3. Installing the needle

CAUTION

Turn off the power switch before installing the needle, otherwise the machine may operate if the start switch is pressed by mistake, which could result in injury.

3039Q

3038Q

3040Q

Use only Schmetz DO x 558 Nm80 - Nm120 needles.

1.Raise the finger guard (1).

2.Loosen the screw (2), and then remove the needle

(3).

3.Insert the new needle (3) as far as it will go so that the groove is facing toward you.

4.Securely tighten the screw (2).

5.Remove the work clamp plates. (Refer to page 26.) Note: After removing the work clamp plates, check that the index mark (4) on the machine head is aligned with the index mark (5) on the looper base before inserting the needle (3) (when the

looper base is turned fully to the right).

6.Lower the finger guard (1).

5-4. Threading the upper thread

CAUTION

Turn off the power switch before threading the thread, otherwise the machine may operate if the start switch is pressed by mistake, which could result in injury.

Thread the upper thread as shown in the illustration below. * Use the accessory needle threader (1).

0875Q

0876Q

<-52 specifications>

(1)

0874Q

2403Q

0878Q

RH-981A

28

Page 34 Page 36
Image 35
Page 34 Page 36
Contents RH-981A Indications Safety InstructionsSymbols Environmental requirements Sewing 3122Q Contents Changing Functions Using Names of Each Part Fly indexer -52 specificationsFly indexer specifications -52 specifications SpecificationsSpecifications PD-9810, Programmer Sewing shapeOptional parts Specifications Replacement parts list for specification changesTable processing diagram InstallationInstalling the motor Installing the control box Installing the motor pulleyInstalling the machine head Lowering the machine head Raising the machine headInstalling the operation panel Installing the oil containerTightening the V-belt Connecting the valve cables Installing the spool standInstalling the hand switch Installing the air unit and the valve unitConnecting the wiring P18 Panel Connections inside the control boxConnecting the air tubes Connecting the motor cablesSecuring the cables To decrease the air pressure Installing the air tubesAdjusting the air pressure To increase the air pressureConnecting the power cord Installing the foot switch option Installing the programmer sold separatelyInstalling the indexer main unit Installing the indexer optionReplacing the plate presser and presser plate Installing the upper thread presserInstalling the valve unit Connecting the connectors Securing the air tubes and cables Installing the hand switch Filling the arm oil tank LubricationAdding oil LubricationRemoving the work clamp plates Oiling the looper, spreader and looper baseChanging the lower thread and gimp trimming Correct USEData initialization Threading the upper thread Installing the needleThreading the lower thread For upper thread trimming specificationsFor upper and lower thread trimming specifications -01, -02 02,-52 Threading the gimpSpecifications Setting the material00, -01, -02 specifications Horizontal setting position Cloth setting positionWhen set to the left setting position Large size specification Installation positionStandard specification Replacing the PROMs Name and function of each operation panel item OperationStarting up Parameter table Taper bar Program setting methodOperation OFF Parameter table Straight bar tacking Operation OFF Cycle program Production counter Using the program memosProgram memo contents Automatic sewing SewingUsing the Emergency Stop switch Upper thread tension Adjusting the thread tensionReference values Explanation of the cutting space function Needle and knife positionRelationship between knife position and eyelet shape Switching between single-pedal and dual-pedal operation Setting the feed bracket to the front positionUsing test feed mode Using manual mode Moving the cloth feed bar -52 specifications Changing the mode during an operationCleaning Cleaning and MaintenanceChecking the air filter Draining the oilLooper height Standard AdjustmentsAdjusting the height of the spreader and looper Spreader heightAdjusting the needle and looper timing Adjusting the loop stroke Adjusting the clearance between the looper and needle Adjusting the height of the needle barAdjusting the spreader mounting positions Adjusting the needle guardAdjusting the needle racking width stitch width Adjusting the spreader timingChanging the knife cutting length Replacing the hammer Filing the cutting surface of the hammer Adjusting the contact between the knife and the hammerAdjusting the contact between the knife and the hammer Replacing the knife Adjusting the cutting pressureAdjusting the position of the work clamp plate Measuring the opening amount Adjusting the cloth opening amountAdjusting the trimming of the lower thread and gimp Adjusting the trimming of the upper threadLower thread presser -02, -52 specifications At the time of shipment Auxiliary clamp arm -02, -52 specificationsAdjusting the cloth feeding speed -52 specifications 3110Q Using the set screw collar Adjusting the indexer hole spacing -52 specificationsAdjusting the position of limit switch R -52 specifications Adjusting the position of limit switch L -52 specificationsChanging Functions Using the Memory Switches Memory switch table Panel DIP switches Changing Functions Using the DIP SwitchesCircuit board DIP switch C Circuit board DIP switchesCircuit board DIP switch D Errors after power is turned on List of Error CodesErrors during operation Hardware errors Needle breaks TroubleshootingProblem Cause Remedy Thread breaks Skipped stitches occurThread slips out Problem Cause Remedy Upper thread is not cutCleanly Lower thread is not cut118-981

rh-918a specifications

The Brother RH-918A is a versatile and innovative machine tailored for both personal and professional use. As a robust electronic sewing machine, it combines functionality and user-friendly features that cater to a wide range of sewing enthusiasts, from beginners to advanced users.

One of the standout features of the Brother RH-918A is its extensive stitch selection. With over 100 built-in stitches, including decorative stitches, utility stitches, and heirloom stitches, users have ample options to choose from, allowing for creativity and customization in every project. The machine also incorporates an easy-to-use stitch selector dial, making it simple for sewists to navigate and find the perfect stitch for their needs.

Another key characteristic of the RH-918A is its automatic needle threader. This time-saving feature allows users to thread the needle effortlessly, reducing eye strain and frustration, especially for those who may struggle with manual threading. Additionally, the top-loading bobbin system facilitates quick bobbin changes and ensures smooth feeding, enhancing overall sewing efficiency.

The machine is equipped with a powerful motor that provides consistent and strong stitches, able to handle various fabric types, from lightweight cotton to heavier materials like denim and canvas. This capability is critical for crafting garments, home décor items, and more intricate projects.

The Brother RH-918A also boasts several convenient features to enhance the user experience. An LED light illuminates the sewing area, making it easier to work on detailed projects, particularly in low-light environments. Furthermore, the machine includes multiple presser feet, such as a zipper foot, buttonhole foot, and walking foot, to expand its functionality and accommodate different sewing techniques.

For enhanced stability, the Brother RH-918A comes with a sturdy metal frame, ensuring durability and precision. Its intuitive interface, comfortable handwheel, and adjustable stitch length and width settings add to the overall ease of use, making sewing enjoyable for everyone.

In summary, the Brother RH-918A combines a wide range of stitches, user-friendly technologies, and robust build quality, making it an excellent choice in the world of sewing machines. Whether for basic repairs or elaborate creations, this machine stands out for its performance and reliability, appealing to a diverse audience of sewing enthusiasts.
Top Page Image Contents