Kenmore 625.38356 Drain ALL Water from Softener, Protect the Water Softener from Freezing

Page 31

PROTECT THE WATER SOFTENER FROM

FREEZING

If the softener is installed where it could freeze (sum- mer cabin, lake home, etc.), you must drain all water

from it to stop possible freeze damage. To drain the sof- tener:

1.Close the shut-off valve on the house main water pipe, near the water meter or pressure tank.

2.Open a faucet in the soft water pipes to vent pres- sure in the softener.

3.Move the stem in a single bypass valve to bypass. Close the inlet and outlet valve in a 3 valve bypass system, and open the bypass valve. If you want water in the house pipes again, reopen the shut-off valve on the main water pipe.

4.Unplug the transformer at the wall outlet. Remove the salt hole cover and the main cover. Take off both drain hoses.

5.Carefully remove the large holding clips at the soften- er inlet and outlet. Separate the softener from the

plastic installation adaptors, or from the bypass valve.

6.Remove the brinewell cover and disconnect the brine valve tubing at the nozzle and venturi assembly. Lift the brine valve out of the brinewell. Tip the brine valve upside down to drain water.

7.Lay a piece of 2 inch thick board near the floor drain. Move the softener close to the drain. SLOWLY and CAREFULLY, tip it over until the rim rests on the wood block with the inlet and outlet over the drain. Do not allow the softener's weight to rest on the inlet and outlet fittings or they will break.

8.Tip the bottom of the softener up a few inches and hold until all water has drained. Leave the softener laying like this until you are ready to use it. Plug the inlet and outlet with rags to keep dirt, bugs, etc. out.

DRAIN ALL WATER FROM SOFTENER

Floor Drain

Wood Block

FIG. 48

Questions? Call The Kenmore Water Line 1-800-426-9345

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Save this Manual Repair or Parts ? Call toll freeTEN Year Limited Warranty Against Leaks ONE Year Limited Warranty on Water SoftenerDisclaimer of implied warranties limitation of remedies Questions? Questions? Call The Kenmore Water Line Small Parts Parts DescriptionsInspect Shipment Pipe Proper Order to Install Water Treating EquipmentPlan Your Installation Tools NeededWhere to Install the Water Softener Typical InstallationDraw Your Pipes Fittings Suggested Slab Foundation InstallationOUT Adding a pressure reducing valve may reduce the flow Before Installing Checks & TestsBypass Valve Assemble Inlet Outlet ADAPTORS, or Single Bypass ValveInlet and Outlet Threaded Adaptors Valve Bypass Installing Holding ClipsBypass Valve Turned Downward Connect the Softener Position Softener Into PlaceConnect Salt Tank Overflow Tubing Connect the Valve Drain HoseSingle Bypass House Main Water Shutoff ValvesLeak Test Cold Water Pipe Grounding Installgroundingclampbetween Thesoftenerinand OUT PipesWater Meter Jumper Wire Connecting TransformerIE,UU InstallcoversProgram the Timer Restart the Water HeaterSET Regeneration Time SET Present Time of DAYSET Water Hardness Number Hardness NumberSanitize Your Water Softener AS Follows Sanitize the Water SoftenerWater Softening Salt with Iron Addingsalttothe StoragetankRemoving Additives Check List of STEP-BY-STEP Guides to Install Salt Monitor System ExtrarechargeRecharge NOW Recharge Tonight12 / 24 Hour Clock Optional Settings Salt EfficiencyCalifornia Efficiency Requirement Water Flow Through the Softener 2Hh,=Program Memory Recharge Time Remaining and Valve Position IndicatorsError Code Kenmores Ultra Cleansing FeatureService Soft Water Service and RegenerationRegeneration Water Flow Through Softener in Backwash Water Flow Through Softener Brining and Brine RinseWater Flow Through Softener Fast Rinse Soft Water Service and Regeneration Automatic BypassElectronics Salt Bridge Salt BridgeIron from Resin BED Cleaning Nozzle & Venturi Keeping the Water Softener CleanProtect the Water Softener from Freezing Drain ALL Water from SoftenerChecklist to Help YOU Save Money Problem Cause Correction625.383560 Timer Code SBypass Valves Model noFlow Rate GPM Pressure Drop PSI vs. Flow Rate GPMEration Check Wiring SchematicFaceplate Always Make These Initial Checks FirstCode Most Likely Possible ProblemProcedure for Removing Error Code From Faceplate Manual Initiated Electronics DiagnosticsTimer PWA Replacement Troubleshooting Valve Position IndicatorsOther Information Cycle Flow Rates Gallons PER MIN Checks, and the manual initiated diagnosticsFloat Setting Manualadvanceregeneration CheckTo Relieve Pressure RotaryvalveserviceDisassembly AssemblyBrining and Brine Rinse Cycle Valve Service CycleWater Flow Through the Softener Fill CycleFast Rinse Cycle Valve Backwash CycleFast Rinse Cycle Backwash CycleRating Decal Location Model Water Softener CompletePart Number Part Description Inlet Outlet Grounding Clamps Brine Valve Assembly Wear-Strip Seal Cross-Section View No. Number Part Description Your Home
Related manuals
Manual 48 pages 50.97 Kb

625.38356 specifications

The Kenmore 625.38356 and 625.39356 models are part of the renowned Kenmore brand, which has built a solid reputation for household appliances over the years. These models are particularly noted for their efficiency, durability, and range of features that cater to the needs of modern households.

One of the standout features of the Kenmore 625.38356 and 625.39356 is their advanced filtration system. Both models come equipped with a multi-stage filtration process that effectively captures allergens, dust, and other particulates from the air. This ensures that you breathe clean air in your home, making these models an excellent choice for allergy sufferers. The HEPA filter included in the design enhances air quality further and is easy to replace.

In terms of performance, both units boast powerful suction capabilities. The powerful motor guarantees effective cleaning across various surfaces, including carpets, hardwood floors, and upholstery. The adjustable height feature allows users to switch between carpet and hard floor settings with ease, providing effective cleaning regardless of the surface type.

Another notable technology integrated into these models is their intelligent sensor technology. This innovation detects the type of debris present and adjusts suction power accordingly, ensuring optimal cleaning performance while also conserving energy. This smart feature aids in extending the lifespan of the vacuum and increasing energy efficiency.

Ergonomics also play a significant role in the design of these Kenmore vacuum models. With adjustable handles and lightweight construction, users can maneuver them easily around their homes. The corded design provides unlimited runtime, eliminating concerns of battery life that can affect cordless models.

Additionally, the Kenmore 625.38356 and 625.39356 feature a variety of attachments designed to enhance versatility. These include crevice tools, dusting brushes, and upholstery attachments. These tools make it easier to clean tight spaces, delicate surfaces, and innovative designs that allow for a thorough clean in every nook and cranny of your home.

Noise levels in these models are also commendably low, making them a quieter option compared to many competitors. This feature allows for comfortable cleaning without disturbing family members or pets.

In summary, the Kenmore 625.38356 and 625.39356 represent a blend of advanced technology, user-friendly design, and powerful performance. Their smart features, superior filtration systems, and effective cleaning mechanisms make them an ideal choice for anyone seeking reliable home cleaning solutions.
Top Page Image Contents