Moen MT302E installation instructions Installation, Flow Director, Flushing

Page 2

Installation

This valve is designed for either CC or IPS connections, depending on the discretion of the installer. If using the IPS connections, thread sealing tape should be used liberally on all threads.

Connect the valve to the supply lines by either means desired. The hot supply should be on the left, the cold supply on the right.

Connect the shower riser pipe to the top outlet and the tub drop pipe to the bottom outlet. Make all connections firm and tight. Block and secure all pipes to the inside wall.

Flow Director

For water supply lines plummed ceiling to floor, please follow these instructions:

Hold the valve with the valve connections in the down position as illustrated below. Use a large flat blade screwdriver and remove the flow director, located in the center port, as illustrated. After removing the flow director, turn the valve over so that the valve connections are in the up position, and reinstall the flow director.

Now the casting can be turned over, with the valve connections facing the ceiling, to accept ceiling-to-valve water supplies.

 

1

 

1

2

2

Trim

 

MAKE SURE ALL WATER SUPPLIES ARE OFF

SHOWER: Assemble shower arm flange to the long end of shower arm. Put thread seal tape on the threads at both ends of the shower arm. Screw shower arm into ell inside wall, do not install showerhead at this time. When a pipe lookout nipple is used, put thread seal tape on the pipe thread and screw the tub diverter spout into the lookout nipple. * CAUTION: spout is ABS plastic and will crack upon contact with some pipe thread compounds. We recommend the use of thread seal tape. Pull out while turning so as not to scratch the wall. If a final turn by a wrench is needed, use a small one with smooth jaws to grip spout end. Do NOT insert a tool into the spout end to turn. You could damage the spout.

Flushing

IMPORTANT:

Pipe chips, sand, stones, and other solids found in new and renovated plumbing can damage the sealing surface of the cartridge and cause a leak. To avoid damage, DO NOT TURN ON THE SUPPLY VALVES until instructed below:

1.After installing and connecting your new faucet, install shower arm and tub spout, open both hot and cold cartridges.

2.Turn on both hot and cold water supply valves and allow the water to run from tub spout for 15 seconds.

3.Pull up on the diverter knob on the tub spout and run water through the shower riser for 15 seconds.

4.Turn off the hot and cold cartridges, install the showerhead and check the system for leaks.

MT302E

Page 1 Page 3
Image 2
Page 1 Page 3
Contents TWO Handle TUB & Shower Valve MeasurementsFlushing InstallationFlow Director Disassembly ReassemblyCleaning and Care Instructions For Special Finish Models Stop Help Line

MT302E specifications

The Moen MT302E is a state-of-the-art kitchen faucet that combines innovative technology with elegant design. This faucet exemplifies Moen's commitment to quality and functionality in the kitchen, making it a popular choice among homeowners and professionals alike.

One of the standout features of the Moen MT302E is its pull-down spray head. This design allows for enhanced maneuverability, making it easy to reach every corner of the sink. The spray head offers two distinct spray functions: stream and spray, catering to various tasks, whether you need a gentle stream for filling pots or a powerful spray for rinsing dishes. With just a simple switch, users can transition between the two modes, ensuring efficiency during cooking and cleaning.

The Moen MT302E also boasts a unique MotionSense technology, which revolutionizes the way you interact with your faucet. This touchless activation feature allows users to turn the water on and off with a simple wave of the hand, making it ideal for handling messy tasks where using handles may not be practical. This functionality not only enhances convenience but also promotes hygiene by minimizing contact with the faucet.

In addition to its practical features, the Moen MT302E is designed with durability in mind. Featuring a robust build and high-quality materials, this faucet is engineered to withstand the rigors of daily use. The finish is not only aesthetically pleasing but also resistant to fingerprints and water spots, ensuring that it maintains its sleek appearance over time.

For ease of installation, the Moen MT302E comes with a Duralock quick connect system, allowing for simple and secure connections. This user-friendly feature simplifies the installation process, making it accessible for both DIY enthusiasts and professionals.

Another notable characteristic of the Moen MT302E is its eco-friendly design. This faucet is designed to conserve water without sacrificing performance. With a flow rate that meets WaterSense guidelines, you can enjoy reduced water consumption while still achieving optimal water pressure.

In summary, the Moen MT302E is a well-rounded kitchen faucet that expertly blends technology, durability, and design. With features like the pull-down sprayer, MotionSense touchless activation, and an eco-friendly approach, it not only enhances the functionality of your kitchen but also adds a touch of modern elegance to your home. Whether you are a culinary enthusiast or someone who values convenience, the Moen MT302E is an excellent choice that promises to elevate your kitchen experience.
Top Page Image Contents