Trim, Make Sure ALL Water Supplies are OFF

Trim

MAKE SURE ALL WATER SUPPLIES ARE OFF

TO INSTALL TRIM AFTER ROUGH-IN

Slide the flange onto the long end of the shower arm. Wrap both ends of shower arm with thread seal tape and screw long end of shower arm into pipe ell inside the wall. Do not install the showerhead.

Install tub spout (see page 2).

Remove screw holding plaster ground and stop tube guard in place and discard. Temporarily install handle. Turn on water, pull up on tub spout diverter knob and flush the shower riser for 15 seconds. Install showerhead and check system for leaks. If there are no leaks, turn OFF water and remove handle and limit stop.

Install escutcheon plate with two screws provided. Mount with the escutcheon notch UP.

Install limit stop(see temperature limit stop section). The notched flat on the cartridge stem must point DOWN when mounting handle.

Handle Attachment :

For handle style A + B . Mount handle on the stem and replace handle screw tightly.

Snap handle insert or plug button in place on the handle.

For handle style C . Mount handle adapter on the stem and replace handle screw tightly. Mount handle on handle adapter and replace set screw.

SHOWERHEAD

TEMPERATURE

LIMIT STOP

ESCUTCHEON

SCREWS (2)

SPOUT

SHOWER ARM

NOTCH

CONNECTIONS

ESCUTCHEON

TUB LOOKOUT NIPPLE

TO REMOVE STOP VALVE

Always turn water supply OFF before disassembly (see disassembly).

Removal of stop valve:

1.Remove handle parts (see disassembly) and escutcheon.

2.Using snap ring pliers, remove retaining ring from valve body.

3.Grip stop valve stem with pliers and rotate slightly to remove from valve body.

Re-Installation of new stop valve:

1.Check to be sure that stop valve stem is fully seated in plug.

2.Insert stop valve until fully seated beyond retaining ring groove in valve body.

3.Using snap ring pliers, place retaining ring in valve body, making sure that ring is fully seated.

4.Check orientation of stop valve for water flow. (Stop is in the off position when screwdriver slot is vertical).

5.Turn water supply on.

Not for use with Moentrol valves.

To Eliminate Cross-Piping On Back-To-Back Installations, or To Correct

Reversed Rough-In Where Hot and Cold Positions Are Reversed:

Remove cartridge assembly, rotate 180 degrees and re-install (see "Reassembly" above). CAUTION: MAKE SURE NOTCH ON STEM IS POINTING UP. Re-install retainer clip, handle washer, stop tube, key stop and handle parts.

HELPLINE: Call our toll free Helpline number,

(800) BUY-MOEN

(289-6636)

for answers to any product, installation, replacement parts, or warranty questions.

MT692C NOV. 02

25300 Al Moen Dr., North Olmsted, OH 44070-8022 U.S.A.

62300, 12342, 12189, 12242, 12341 specifications

Moen has established itself as a leading brand in the realm of kitchen and bathroom fixtures, and its TL183CP, TL183P, TL182CP, TL182, and TL183 faucets are testament to the brand’s commitment to quality, innovation, and style. Each model showcases unique features and cutting-edge technologies that enhance user experience while ensuring aesthetic appeal.

The Moen TL183 series boasts a sleek, modern design characterized by its smooth lines and polished finishes, seamlessly integrating into various decor styles. The faucets are available in chrome, which provides a reflective, shiny surface, as well as other finishes, allowing homeowners to choose based on personal preference and kitchen or bathroom scheme.

A standout feature of these faucets is Moen’s Spot Resist technology. This innovative coating helps to minimize water spots and fingerprints, keeping the faucet looking clean and allowing for easy maintenance. This is particularly valuable in busy kitchens or bathrooms where aesthetics can quickly deteriorate.

The TL183 and TL182 models come equipped with the Duralock Quick Connect system. This technology simplifies installation, allowing homeowners to easily connect and disconnect the water supply lines without the need for additional tools. This not only saves time during installation but also provides peace of mind knowing that the connections are secure.

Another noteworthy characteristic is the incorporation of Moen’s Reflex system in the TL183P and TL182CP models. This advanced feature offers smooth operation of the spray head, allowing for greater flexibility and range of motion. The spray head retracts seamlessly, which prevents tangling and ensures that the user can easily switch between different spray modes, including a powerful spray for cleaning and a gentle stream for filling pots.

All models in the TL183 series are designed for comfort and usability, featuring ergonomic handles that allow for easy temperature adjustment. The inclusion of the lasting and durable cartridge technology ensures that the faucets maintain consistent performance over time without the risk of leaks.

In summary, the Moen TL183CP, TL183P, TL182CP, TL182, and TL183 faucets embody the perfect blend of style, technology, and functionality. With features like Spot Resist technology, Duralock Quick Connect, and the Reflex system, these faucets not only enhance the beauty of your sinks but also elevate the everyday experience of your kitchen or bathroom. They are a prime example of how innovation in design can lead to practical solutions in home interiors.