Disassembly, Reassembly | Moen 2200 Series, 2400 Series specs

➤

RETAINER CLIP

Disassembly

Turn OFF both hot and cold water supplies, then open faucet to relieve pressure. Remove handle cover from handle knob. Take out handle screw and remove handle knob, washer, and stop tube. Lift out retainer clip. Rotate cartridge shell back and forth with Moen cartridge twist wrench, grasp the cartridge stem with pliers, and pull out the cartridge.

BODY

CASTING

➤

	NOTCHED FLAT
	ON STEM
	➤
	➤
➤	➤

HANDLE KNOB SERVICE KIT

O-RING

WASHER

➤ ➤

➤	➤

NOT SHOWN

ESCUTCHEON AND

EAR

➤

HANDLE

ESCUTCHEON

SCREWS

Reassembly

	REPLACEMENT	STOP TUBE
	CARTRIDGE	STOP TUBE
	CARTRIDGE

DIVERTER

KNOBHANDLE COVER SCREW

Re-insert cartridge by pushing it all the way into the body until the front of the ears on the cartridge shell are flush and aligned with the body, (see illustration). Replace the retainer clip so that the legs straddle the cartridge ears and slide down into the bottom slot in the body. This prevents the cartridge from rotating and locks it in the body. The notched flat on the stem must point UP when mounting handle, with pointer UP. Re-install stop tube, handle parts and handle knob or lever. Tighten handle screw securely and replace handle cover.

TO REMOVE STOP VALVE

Always turn water supply OFF before disassembly. Open faucet to alleviate sustained pressure.

Removal of stop valve:

1.Remove knob and escutcheon (pry off handle cap and remove handle screw).

2.Using snap ring pliers, remove retaining ring from valve body.

3.Grip stop valve stem with pliers and rotate slightly to remove from valve body.

Re-Installation of new stop valve:

1.Check to be sure that stop valve stem is fully seated in plug.

2.Insert stop valve until fully seated beyond retaining ring groove in valve body.

3.Using snap ring pliers, place retaining ring in valve body, making sure that ring is fully seated.

4.Check orientation of stop valve for water flow. (Stop is in the off position when screwdriver slot is vertical).

5.Turn water supply on.

Not for use with Moentrol valves.

Trim MAKE SURE ALL WATER SUPPLIES ARE OFF.

C.C.

FLANGE

SHOWERHEAD

SHOWER ARM

ESCUTCHEON

SCREWS (2)

I.P.S.

SHOWER: Install flange on long end of arm. Wrap threads on both ends of shower arm with Teflon tape. Screw long end of shower arm into wall. Install flange and showerhead.

C.C.SPOUT: The Moen Slip Fit spout is designed with an O-ring seal. It is specifically designed for installation with copper water tube. Lookout must be free from burrs inside and out. The edge must not be rolled inward from a dull tubing cutter. The outside surface must be free from nicks and scratches.

Press and twist the spout onto the lookout upside down. Tighten the clamp screw with a 5/32" hex wrench until it just starts to bind. Turn spout upright into position against the wall and finish tightening the clamp screw by hand. The use of pliers or another wrench on the hex wrench is not necessary. Do not overtighten.

CLAMP SCREW

	TUB LOOKOUT
ESCUTCHEON	NIPPLE
	I.P.S.

TUB SPOUT

IPS SPOUT:

CAUTION: This spout is A.B.S. plastic and will crack when in contact with some pipe thread compounds. We recommend using Teflon tape thread sealant.

C.C.

Please read the pipe compound label to be certain.

Screw tub spout onto pipe and tighten by hand. If final turn by wrench is needed, use small wrench with smooth jaws; otherwise, pad wrench teeth with rag as shown. DO NOT INSERT TOOL INTO SPOUT END TO TURN SPOUT.

ESCUTCHEON: Remove screw holding plaster ground in place. Discard plaster ground. Temporarily install handle knob. Turn on water and check system for leaks. If there are no leaks, turn OFF water and remove handle knob. Install escutcheon plate with two screws provided Mount with the notch UP. Install stop tube. The notched flat on the cartridge stem must point UP when mounting the handle knob. Mount handle knob on the stem and replace handle screw tightly. Snap handle cover in place on the handle.

IMPORTANT FINAL CHECK: If above instructions have been followed correctly there will be clearance between the handle and the escutcheon when the handle is pushed into the closed position, otherwise the valve will not shut off.

2200 Series, 2400 Series specifications

The Moen 2400 Series and 2200 Series represent a blend of innovation, functionality, and style in the realm of plumbing fixtures. Designed for modern kitchens and bathrooms, these series offer consumers an exceptional balance of performance and aesthetic appeal.

The Moen 2400 Series is renowned for its seamless operation and user-friendly features. One of its standout attributes is the convenience of the Duralast cartridge, which ensures a consistent water flow and temperature control. This technology not only enhances the user experience but also promotes durability, reducing the need for frequent replacements. The 2400 series is equipped with a powerful and efficient streamline design that allows for easy gripping and maneuverability, making it suitable for all users.

Additionally, the 2400 Series faucet features a pull-down spray head that offers a choice of spray patterns. Whether it’s a powerful rinse or a gentle spray, users can switch functions with ease. The faucet is also built with Spot Resist Stainless finish, which resists fingerprints and water spots, keeping the fixture looking pristine.

On the other hand, the Moen 2200 Series takes a more classic approach while incorporating modern necessities. This series features a high arc design that provides ample clearance for pots and pans, enhancing overall kitchen functionality. The 2200 Series emphasizes durability with its robust construction materials and the Moen’s exclusive Lifeshine finish, ensuring that users can enjoy the flawless appearance for years.

Both series come equipped with the innovative Moen MotionSense technology, allowing for hands-free operation of the faucet. This feature is not only hygienic but also enhances efficiency, particularly in busy environments where multitasking is common. The 2200 Series goes a step further with its Eco-Performance models, which utilize advanced aeration technology to conserve water without sacrificing pressure.

Another important characteristic shared by both series is Moen's commitment to sustainability. Each fixture is designed to meet or exceed the strict WaterSense standards, promoting conservation while delivering a high-performance experience.

In conclusion, both the Moen 2400 Series and 2200 Series stand out for their unique combination of technology, efficiency, and style. They offer a wide range of features that cater to the modern homeowner's needs, making them an excellent choice for anyone looking to upgrade their kitchen or bathroom fixtures. Whether opting for the modern flair of the 2400 Series or the classic elegance of the 2200 Series, consumers can trust Moen to deliver quality and reliability.