American Standard 3354 16 2mm, Nuts, 16 7mm, To take full loading from the fixture allowing, Turn

Page 2

3

 

 

 

Place back-up nuts on both bottom bolts, and

4

 

 

Using a level, adjust the top left back-up nut so that

 

 

 

 

 

 

 

 

 

 

 

 

 

 

the top left-hand bolt only.

 

 

 

it is in the same vertical plane as the lower left back-up

 

 

 

 

Adjust the two lower back-up nuts so that front

 

 

 

nut. (If wall surface is irregular, the three back-up

 

 

 

 

 

 

 

 

 

 

 

 

nuts must be positioned to allow a minimum 1/16"

 

 

 

 

face of nuts is flush with finished wall.

 

 

 

 

 

 

 

 

 

 

gap between fixture and wall surface.)

 

 

 

 

 

 

 

 

Adjust waste horn to project 5/16" (7mm) from finished wall.

 

FINISHED WALL

FINISHED WALL

1/16" (2mm)

 

(IRREGULAR

 

WALL SURFACE)

CLOSET

 

CARRIER

 

SYSTEM

 

(3) NUTS

LEVEL

 

WASTE

 

HORN

 

5/16" (7mm)

 

5

 

 

 

 

AMERICAN-STANDARD ONE-YEAR LIMITED WARRANTY

 

 

 

 

NOTE: Bearing nuts and washers must be set

If inspection of this American-Standard plumbing product, within one year after its

 

 

 

 

 

 

 

 

 

 

to take full loading from the fixture allowing

initial installation, confirms that it is defective in materials or workmanship,

 

 

 

 

American-Standard will repair or, at its option, exchange the product for a similar

 

 

 

 

1/16" (2mm) clearance between fixture and wall.

model.

 

 

 

 

 

 

This warranty does not apply to local building code compliance. Since local

 

 

 

 

Follow support manufacturer's recommended

building codes vary considerably, the purchaser of this product should check with a

 

 

 

 

local building or plumbing contractor to insure local code compliance before

 

 

 

 

 

 

 

 

setting of closet outlet connection.

installation.

 

 

 

 

 

This warranty shall be void if the product has been moved from its initial place of

 

 

 

 

 

 

 

 

 

 

installation; if it has been subjected to faulty maintenance, abuse, misuse, accident or

 

 

 

 

Place felt or neoprene gasket (wax ring not

other damage; if it was not installed

in accordance with American-Standard's

 

 

 

 

 

 

 

 

instructions; or if it has been modified in a manner inconsistent with the product as

 

 

 

 

recommended) on closet outlet.

 

 

 

 

shipped by American-Standard.

 

 

 

 

 

 

American-Standard's option to repair or exchange the product under this warranty

 

 

 

 

When the fixture is installed, closet outlet

does not cover any labor or other costs of removal or installation, nor shall

 

 

 

 

American-Standard be responsible for any other incidental or consequential

 

 

 

 

 

 

 

 

gasket must be compressed sufficiently to

damages attributable to a product defect or to the repair or exchange of a

 

 

 

 

defective product, all of which are expressly excluded from this warranty. (Some

 

 

 

 

assure a gas and watertight seal.

 

 

 

 

states or provinces do not allow the exclusion or limitation of implied warranties, so this

 

 

 

 

 

exclusion may not apply to you.)

 

 

 

The following steps require a helper:

This warranty gives you specific legal rights. You may have other statutory rights

 

 

 

 

 

that vary from state to state or from province to province, in which case this warranty

 

 

 

 

Install bowl on support using cap nuts and fiber

does not affect such statutory rights.

 

 

 

 

 

For service under this warranty, it is suggested that a claim be made through the

 

 

 

 

 

 

 

 

washers with the back-up nuts and washers.

 

 

 

 

contractor or dealer from or through whom the product was purchased, or that a

 

 

 

 

 

service request (including a description of the product model and of the defect) be

 

 

 

 

DO NOT APPLY TOP RIGHT FIBER WASHER

sent to the following address:

 

 

 

 

 

 

 

 

 

 

 

AND CAP NUT UNTIL OTHER CAP NUTS

In the United States:

In Canada:

 

 

 

 

HAVE BEEN FIRMLY TIGHTENED USING A

American Standard Inc.

American-Standard

 

 

 

 

P.O. Box 6820

2480 Stanfield Road

 

 

 

 

WRENCH.

Piscataway, New Jersey 08855

Mississauga, Ontario

 

 

 

 

 

Attention: Director of Consumer Affairs

Canada L4Y 1S2

 

 

 

 

Install top right cap nut with fiber washer and

For residents of the United States,

Toll Free: (800) 387-0369

 

 

 

 

 

 

 

 

warranty information may also be

 

 

 

 

run up hand tight. Wrench tighten approximately

www.americanstandard.ca

 

 

 

 

obtained by calling the following

 

 

 

 

 

 

 

 

 

1/4 turn.

toll free number: (800) 442-1902

 

 

 

 

 

www.americanstandard-us.com

 

 

 

 

 

Apply sealant to gap between bowl and finished

In Mexico:

 

 

 

 

Customer Service Manager

 

 

 

 

 

 

 

 

wall. Remove excess sealant.

Ideal Standard, S.A. de C.V.

 

 

 

 

 

Via Morelos #330

 

 

 

 

 

Col. Santa Clara

 

 

 

 

 

Ecatepec 55540 Edo. Mexico

 

 

 

 

 

www.americanstandard.com.mx

7301115-100 Rev. B

- 2 -

 

Image 2
Contents E F O R Fixture MountingT U R E 7301115-100 Rev. BInstall bowl on support using cap nuts and fiber Setting of closet outlet connectionWhen the fixture is installed, closet outlet Install top right cap nut with fiber washer