Mitsubishi Electronics MCF-D24VD, MCF-D18VD Name of Each Part, Preparation Before Operation

Page 4

• OPERATING INSTRUCTIONS •

NAME OF EACH PART

Indoor unit

Remote controller

Horizontal vane Vertical vane

Display section

Operation indicator lamp

Remote control receiving section

Front panel Air inlet

Air cleaning fi lter (Option)

Air fi lter

Deodorizing fi lter (Option)

Emergency operation switch Page 4

Operation display section

ON/OFF

(operate/stop) button

FAN speed control button

Page 5

I FEEL

COOL

Signal transmitting section Distance of signal : About 6 m

Beep (s) is (are) heard from the indoor unit when the signal is received.

AMPM

AMPM

Temperature buttons

Page 4

Off-timer button Page 6

When installed on the ceiling

Outdoor unit

Air inlet (back and side)

Piping

Drainage hose

Operation select button

Page 4

VANE control button

Page 5

FAN

DRY

On-timer button Page 6

TIME set buttons Pages 3, 5

HR. button MIN. button

CLOCK button Page 3

RESET button Page 3

Lid

Slide down to open

Remote controller holder

Air outlet

Drain outlet

Appearance of the outdoor unit may differ from some models.

• Install the remote control- ler holder to a place where the signal can be received by the indoor unit.

Use the remote controller provided with the unit only.

Do not use other remote controllers.

PREPARATION BEFORE OPERATION

Before operation: Insert the power supply plug into the power outlet and/or turn the breaker on.

Installing the remote controller batteries

4. Press RESET

1. Remove the front lid

S

 

ET

C

 

 

LO

 

CK

2. Insert AAA alkaline batteries

3. Install the front lid

Make sure the polarity of the batteries is correct.

Do not use manganese batteries. The remote controller could malfunction.

Do not use rechargeable batteries.

Replace all batteries with new ones of the same type.

Batteries can be used for approximately 1 year. However, batteries with expired shelf lives last shorter.

Press RESET gently using a thin stick.

If the RESET button is not pressed, the remote controller may not operate correctly.

Setting current time

1. Press CLOCK

RESET

LOCK

 

 

2. Press the

and

buttons

3.

 

to set the time

 

Press CLOCK again

Each time

is pressed, the

set time

increases by 1

 

 

hour, and each time is pressed, the set time increases by 1 minute.

• Press CLOCK gently using a thin stick.

En-3

Image 4
Contents SPLIT-TYPE AIR Conditioners Contents Do not pull the power cord Do not operate switches with wet handsConsult your dealer for installing the air conditioner Provide a dedicated power supply for the air conditionerName of Each Part Preparation Before OperationOperation indicator lamp Feel modeCool mode DRY modeDirection Adjustment FAN Speed and AirflowCleaning Air cleaning filter OptionAir filter Catechin air filter Deodorizing filter OptionWhen YOU Think That Trouble has Occurred Installation Place and Electrical Work SpecificationsWhen using the air conditioner again Installation placeสารบัญ อควรระวังเพื่อความปลอดภัยามใชสวิตชขณะมือเปยก ตัวเครื่องอยาดึงสายไฟ กองไฟชื่อของสวนประกอบตางๆ การเตรียมตัวกอนใชงานรีโมทคอนโทรล กดปุมCLOCKการเลือกโหมดการใชงาน ไฟแสดงการทํางานหรือ กะพริบ แบบตั้งพื้นแบบแขวนใตเพดาน แบบตั้งพื้นแบบแขวนใตเพดานทำความสะอาดทุก 2 สัปดาห ทำความสะอาดทุก 2 เดือนเมื่อทานคิดวาเครื่องปรับอากาศของทานมีปญหา เปนเวลานานสถานที่ติดตั้งและงานทางดานไฟฟ อมูลจำเพาะVN79B582H01