Mitsubishi Electronics MCFZ-A12WV FEEL... Auto Operation, Description of I FEEL... mode

TOO

WARM

I FEEL... AUTO OPERATION

With the “ (I FEEL...)” auto operation mode, the optimum room condition can be set automatically with a one-touch operation.

Description of “I FEEL...” mode

Details of operation

˚C

CLOCK

AMPM

12345

AMPM

ON/OFF TOO TOO

WARM COOL

	FAN	STOP
I FEEL
HEAT	AUTO
	VANE	START
DRY	COOL
MODE		HR.
ECONO COOL		MIN.
	RESET CLOCK

To start operation:

■ Press the	ON/OFF
	button.

When the “ (I FEEL...)” mode is selected, the air conditioner is automatically controlled at the optimum temperature.

To stop operation:

■ Press the	ON/OFF
	button.

If you feel slightly warm:

■ Press the button to lower the temperature.

One press lowers the temperature by about 1°C.

If you feel slightly cool:

According to the room temperature when the operation starts, the operation mode is automatically set to COOL, DRY or HEAT. However, when operation is started again within 2 hours after it is stopped, the same operation mode before the

operation is stopped is selected. The operation mode selected first is not changed even if the room temperature changes. If the operation mode does not match the room condition, select the appropriate operation mode by pressing the MODE

button.

Details of auto operation

Room temperature	Operation mode	Target temperature
when started		(initial state)
About 25°C or higher	COOL	About 24°C
About 25°C to 23°C	DRY	—
About 23°C or lower	HEAT	About 26°C

NOTE:

COOL: When the room temperature is 2°C higher than the set temperature, the set temperature may not be changed since the air conditioner is operating to reach the target (set) temperature. In this case, please wait until the room temperature drops to within 2°C of the set temperature and then change the set

■ TOO

Press the COOL button to raise the temperature.

One press raises the temperature by about 1°C.

temperature.

HEAT: When the room temperature is 2°C lower than the set temperature, the set temperature may not be changed since the air conditioner is operating to reach the target (set) temperature. In this case, please wait until the room temperature rises to within 2°C of the set temperature and then change the set temperature.

MODE

When “ (I FEEL...)” is not selected, press the button until it is set.

Each time the button is pressed, the operation mode is changed

in sequence: (I FEEL...) → (AUTO) → (COOL) → (DRY) →(HEAT)

I FEEL

HEAT AUTO

DRY COOL

MODE

FAN

VANE

STOP

START

HR.

Details of display on the indoor unit

The operation indicator at the right side of the indoor unit indicates the operation state.

Operation Indicator	Lighted
	Not lighted

ECONO COOL MIN

Description of “AUTO RESTART FUNCTION”

•These units are equipped with an auto restart function. When the main power is turned on, the air conditioner will start operation automatically in the same mode as the one set with the remote controller before the shutoff of the main power.

•If the unit was set to off with the remote controller before the shutoff of the main power, it will remain stopped even after the main power is turned on.

•If the unit was in the emergency operation before the shutoff of the main power, it will start operation, when main power comes on, in the same mode as the one set with the remote controller before the emergency operation.

•If the unit is operated in “I FEEL...” or “AUTO” mode before power failure, the operation mode (COOL, DRY or HEAT) is not stored in the memory. When the main power is turned on, the unit decides the operation mode by the initial room temperature at restart and starts operation again.

Operation indicator lamp

Indication	Operation state	Difference between target
		temperature and room temperature
	This shows that the air conditioner is operating to reach the
	target temperature. Please wait until the target temperature	About 2°C or more
	is obtained.
	This shows that the room temperature is approaching the	About 2°C or less
	target temperature.

6