Maytag W10274302B, LI3VQA Installation Requirements, Tools and Parts, Location Requirements

Page 4

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

Tools needed

Drill

1¹⁄₄" (3.0 cm) drill bit

¹⁄₈" (3.0 mm) drill bit for pilot holes

Pencil

Wire stripper or utility knife

Tape measure or ruler

Caulking gun and weatherproof caulking compound

Flat-blade screwdriver

Phillips screwdriver

For vented installations, you also need:

Saber or keyhole saw

Vent clamps

Metal snips

Compass or 8" (20.3 cm) circle template

Parts supplied

Remove parts from package. Check that all parts are included.

2 - Metal filters

6 - 4.5 x 13 mm mounting screws

3 - 4 x 8 mm damper screws

3¹⁄₄" x 10" (8.3 x 25.4 cm) damper/vent connector

4 - 5 x 45 mm screws

4 - 8 x 40 mm wall anchors

Recirculating kit

Charcoal filters for non-vented (recirculating) installations. See the “Assistance or Service” section to order replacement filters.

Parts needed

For vented installations:

3¹⁄₄" x 10" (8.3 x 25.4 cm) or 6" (15.2 cm) or larger round metal venting

6" (15.2 cm) or larger round damper, if using 6" (15.2 cm) or larger round vent system

3¹⁄₄" x 10" (8.3 x 25.4 cm) to 6" (15.2 cm) or larger diameter transition piece if using 6" (15.2 cm) or larger diameter round vent system.

For cabinets with recessed bottoms:

Two 2" (5.1 cm) wide filler strips. Length and thickness determined by recess dimensions.

Four flat head wood screws or machine screws with washers and nuts (to attach filler strips).

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

It is the installer’s responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located inside the range hood on the left wall.

Range hood location should be away from strong draft areas, such as windows, doors and strong heating vents.

Cabinet opening dimensions that are shown must be used. Given dimensions provide minimum clearance. Consult the cooktop/range manufacturer installation instructions before making any cutouts.

Grounded electrical outlet is required. See “Electrical Requirements” section.

The hood is factory-set for vented installations. For non- vented (recirculating) installations, the Recirculation Kit is included. See the “Assistance or Service” section to order Replacement Charcoal Filters Part Number W10272068.

All openings in ceiling and wall where range hood will be installed must be sealed.

For Mobile Home Installations

The installation of this range hood must conform to the Manufactured Home Construction Safety Standards, Title 24 CFR, Part 328 (formerly the Federal Standard for Mobile Home Construction and Safety, title 24, HUD, Part 280) or when such standard is not applicable, the standard for Manufactured Home Installation 1982 (Manufactured Home Sites, Communities and Setups) ANSI A225.1/NFPA 501A*, or latest edition, or with local codes.

Product Dimensions

 

 

1³⁄₁₆"

12"

 

(3.0 cm)

 

 

(30.5 cm)

 

 

7¹⁄₄"

 

(18.4 cm)

3" (7.6 cm) -

2"

⁵⁄₈"

30" (76.2 cm) model

(1.6 cm)

5 ³⁄₄" (14.6 cm) -

(5.1 cm)

 

36" (91.4 cm) model

9"

 

 

 

(22.9 cm)

 

 

 

⁵⁄₈"

 

 

(1.6 cm)

 

29 ⁷⁄₈" (75.9 cm) - 30" (76.2 cm) model

 

19³⁄₄"

 

 

(50.2 cm)

 

35 ⁷⁄₈" (91.1 cm) - 36" (91.4 cm) model

 

 

 

 

 

4

Image 4
Contents Hotte D’ASPIRATION DE Range Hood Safety Table of ContentsImportant Safety Instructions Tools and Parts Installation RequirementsLocation Requirements Installation Clearances Cold Weather InstallationsVenting Requirements Makeup AirElectrical Requirements Calculating Vent System LengthCm or Larger Round Vent System Example vent systemInstallation Instructions Determine Wiring Hole LocationTo wire through top Prepare LocationWall Venting Install Vent SystemTo make a 3½ x 10½ 8.9 cm x 26.7 cm rectangle in the wall Install Range Hood For Vented Installations Only Complete InstallationRange Hood USE Range Hood Care CleaningRange Hood Controls Wiring Diagram Assistance or Service AccessoriesU.S.A CanadaWhirlpool Corporation Major Appliance Warranty This limited warranty does not coverSécurité DE LA Hotte DE Cuisinière Votre sécurité et celle des autres est très importanteImportantes Instructions DE Sécurité Exigences demplacement Exigences DinstallationOutils et pièces Installations pour régions à climat froid Exigences concernant lévacuationDégagements de séparation à respecter Air dappointSystème de décharge de 3¹⁄₄ x 10 8,3 cm x 25,4 cm Exemple de système de déchargeCalcul de la longueur effective du circuit dévacuation Préparation de lemplacement Instructions DinstallationSpécifications électriques Évacuation par le mur Déterminer l’emplacement du trou de passage du câbleCâblage à travers le sommet du placard Installation de la hotte Installation du conduit d’évacuationTrou en forme de serrure Achever l’installation Commandes de la hotte de cuisinièreCommande de la lampe Utilisation DE LA HotteEntretien DE LA Hotte NettoyageSchéma DE Câblage CordondalimentationAssistance OU Service AccessoiresGarantie DES Gros Appareils Ménagers Whirlpool Corporation Au CanadaW10274302B

LI3VQA, W10274302B specifications

The Maytag W10274302B, also known as the LI3VQA, is an innovative addition to the realm of home appliances, specifically designed to enhance the functionality of your kitchen. This refrigerator model stands out for its robust features, advanced technologies, and user-friendly characteristics, making it an excellent choice for modern households.

One of the main features of the Maytag LI3VQA is its spacious interior. The refrigerator boasts a generous capacity, ensuring ample room for all your groceries, from fresh produce to frozen items. Its adjustable shelving allows for customized storage options, accommodating larger items with ease. Furthermore, the crisper drawers are designed to maintain optimal humidity levels, ensuring that fruits and vegetables stay fresh longer.

The LI3VQA is equipped with Maytag's innovative PowerCold feature, which quickly chills the refrigerator and freezer compartments after loading them with warm items. This technology ensures that your food reaches safe temperatures rapidly, minimizing food spoilage. Additionally, the refrigerator includes a built-in ice maker and an advanced water filtration system, providing chilled, filtered water and ice on demand.

Energy efficiency is another standout characteristic of this model. The Maytag LI3VQA is Energy Star certified, which means it meets strict energy efficiency guidelines set by the U.S. Environmental Protection Agency. This certification not only helps reduce your carbon footprint but also leads to lower energy bills.

Another noteworthy technology within the Maytag W10274302B is its unique fingerprint-resistant finish. This feature keeps the surface cleaner for longer periods, reducing the need for frequent cleaning and ensuring that your refrigerator maintains its sleek appearance.

Furthermore, the refrigerator is equipped with bright, LED interior lighting that illuminates the entire space, making it easy to find items even in low light conditions. The door bins are also designed for easy access, allowing for convenient storage of condiments and smaller items.

In summary, the Maytag W10274302B, LI3VQA is a feature-rich refrigerator that combines practicality with advanced technology. With its spacious design, efficient cooling systems, and energy-saving capabilities, it caters to the needs of busy households while promoting a sustainable lifestyle. This model exemplifies what modern refrigeration should aspire to be, making it a worthy investment for any kitchen.