Electrolux E23CS78HSS specifications Cutout Dimensions, Collar Kit, Top Trim Piece

Counter-Depth Refrigerator

E23CS78HSS designer series

		Standard
		Refrigerator Depth
		vs. Counter Depth
	A	Counter Depth
		235/8"
	C
Cutout	B
Dimensions
Standard	With Collar Kit
“Built-In Look”	(ECK23CDS)

26 7/8" 35 5/8"

7 5/8"

69 5/16"

68 3/16"	Water
with	line inlet
3/8"	location
rollers	(left
	bottom
	rear)

(A) 70 1/4"	(A) 70 1/4"
(B) 36"	(B) 36 1/8"
(C) 24"	(C) 24 1/2"

Collar Kit -

Side Trim Piece

Magnetic Tape Refrigerator Case

Door Gasket

281/2"

Standard Depth

3/4" Cabinet

Side Panel

1/2" Cabinet

Side Panel

Side Trim Piece

Side trim must be installed flush with the gasket contact surface on the refrigerator case.

Power cord location (right bottom rear)

Allow at least 45 1/4" with	23 5/8"
doors in 90° open position	29 3/8" to handle
	extension
Recessed water line	Recessed electrical outlet
7/8" Airspace

Collar Kit -	Overhead
Top Trim Piece	Cabinet Door
	Top Trim Piece
Cabinet Underside	1" min.
	Clearance

Refrigerator Case

24"	(5/8" gap + 1/4" wall plates)	25"
	24 1/2" Side Panel, 1/2" min. width
Cabinet		Countertop
	(with Collar Kit trim)
	24" Side Panel, 1/2" min. width
	(without Collar Kit trim)
	Collar Kit - Side Trim Pieces

Counter-Depth Refrigerator Specifications

•Product Weight – 300 Lbs.

•Voltage Rating – 120V/60 Hz/15 or 20 Amps

•Connected Load (kW Rating) @120 Volts = 1.02kW

(For use on adequately wired 120V, dedicated circuit having 2-wire service with a separate ground wire. Appliance must be grounded for safe operation.)

•Amps @120 Volts = 8.5 Amps

•Always consult local and/or national electric & plumbing codes.

•When installing next to wall allow 3-1/2" handle clearance.

•If optional Collar Kit (ECK23CDS) is to be used, refer to Collar Kit specifications on this page for different cutout dimensions.

•If optional Louvered Trim Kit (4480) is to be used, refer to Louvered Trim Kit (4480) Installation Specifications page on web for different cutout dimensions.

Standard “Built-In Look” Specifications

•Minimum opening of 70-1/4"H x 36"W x 24"D required for standard “Built-In Look.” (70-1/4" H to be measured from finished floor to underside of soffit or overhead cabinet.)

•Remove all wall/floor molding prior to installation.

•Water recess on rear wall recommended to prevent water line damage. Minimum recommended size tubing is 48" x 1/4".

•Front rollers are adjustable for “Built-In Look.”

Optional Collar Kit (ECK23CDS) Specifications

•To use optional Collar Kit, an enclosure is required around refrigerator having a minimum opening of 70-1/4"H x 36-1/8"W x 24-1/2"D with 1/2" minimum side panels.

•Add maximum of 1/4" to 70-1/4" opening height when installed with frameless-style overhead cabinets, for door opening clearance.

•The cabinet or soffit above refrigerator must extend out to same depth as side panels.

•To provide additional clearance for overhead cabinet doors when in open position, allow 1" from underside of cabinet to bottom of cabinet door.

•A minimum width of 36-1/8" is required for refrigerator installation with an additional 1/2" or 3/4" added for each side panel.

•If 1/2" side panels are used, then side trim piece and panel will be even. If 3/4" side panels are used, then 1/4" of side panel will extend beyond collar trim and must be finished.

Note: For planning purposes only. Refer to Product Installation Guide on the web at electroluxicon.com for detailed instructions.

Optional Accessories

•Collar Kit – (ECK23CDS).

•Louvered Trim Kit – (4480).

USA • 250 Bobby Jones Expressway • Augusta, GA 30907 • 1-877-4electrolux (1-877-435-3287) • electroluxicon.com	High standards of quality at Electrolux Home Products, Inc. mean we are
	constantly working to improve our products. We reserve the right to change
CANADA • 5855 Terry Fox Way • Mississauga, ON L5V 3E4 • 1-800-265-8352 • electroluxicon.ca
	specifications or discontinue models without notice.

E23CS78HSS 03/08 © 2008 Electrolux Home Products, Inc. Printed in the U.S.A.