Installation
Flush Mounting
For new pool construction and modification of older pools, installing the UW30 flush with the sides of the pool makes a very neat and unobtrusive installation. The speaker is mounted in a wet‑niche (Paragon Part #68102 or equivalent) in the same manner as an underwater light. Figure 1 shows a typical installation. The speaker is mounted up to 1.2 m (4 ft.) below the surface of the water and flush with the side of the pool. (For installation in water depths lower than recommended, please contact factory.) A marine plywood or stainless steel mounting ring or face plate is recommended. (Paragon Part # 68103SS stainless steel or #68103 bronze polished chrome or equivalent). Several pool equipment manufacturers have
at: KDI Paragon, Inc., 341 Route 55 Westwing, LaGrangeville, NY
12540, Phone: (845)
Fusing
For maximum protection against speaker overload, fusing the line from the amplifier is recommended. In the event of accidental overload, it is much easier to replace a fuse (which is above the water) than to replace or have the speaker repaired. Installing a 25 ohm, 20 watt resistor in parallel with a 1.5 ampere, fastblowing fuse in series with the speaker is recommended. See Figure 2.
Layout of Speaker in Pool
When underwater speakers are installed, particularly in smaller pools where only one or two speakers are needed, they should be located in the deep end of the pool. The above recommendation will effectively equalize the intensity of sound throughout the pool. For installations in large pools, such as at country clubs, municipal facilities, etc., the speakers should be located around the periphery of the pool. A good rule to follow for large pools is one speaker for every 900 square feet (83.61 square meters) of pool surface at the deep end and one speaker for every 1,200 square feet (111.48 square meters) of pool surface for the shallow end. Of course, for high‑noise conditions in the pool, the number of speakers should be doubled for best results.
Figure 2
Fuse Recommendation
Figure 1
Typical Installation of a KDI Paragon
America:
USA: Telex Communications Inc. 12000 Portland Ave South, Burnsville, MN 55337, USA, Phone:
Western Canada: PAG Canada. 23 Hawkesbury Crescent, Winnipeg, MB
Eastern Canada: PAG Canada. 728 Eglinton Ave. East, Toronto, ON M4G 2K7, Canada, Phone:
Québec: Acoustik GE Inc. 5715 Kincourt, Montréal, PQ H4W 1Y7, Canada, Phone:
Mexico: Telex Communications de Mexico. Parque Chapultepec
Latin America: Telex Communications Inc. 12000 Portland Ave South, Burnsville, MN 55337, USA, Phone:
Germany: Telex EVI Audio GmbH. Hirschberger Ring 45, D 94315, Straubing, Germany, Phone: +49
France: EVI Audio France S.A. Parc de Courcerin, Allée Lech Walesa, F 77185 Lognes, France, Phone: +33
UK: Telex Communications Ltd. 4, The Willows Centre, Willow Lane, Mitcham, Surrey CR4 4NX, UK, Phone: +44 208 646 7114, Fax: +44 208 640 7583
Africa &
Japan: EVI Audio Japan Ltd.
Australia: EVI Audio (Aust) Pty Ltd. Slough Business Estate, Unit 23, Silverwater, N.S.W. 2128, Australia, Phone: +61
China: EVI Audio (HK) Ltd. Unit E & F, 21F, Luk Hop Industrial Bldg., 8 Luk Hop St., San PO Kong, Kowloon, Phone: +852
Singapore: Telex Pte. Ltd. 3015A Ubi Road 1,
© Telex Communications, Inc. 02/2010
Figure 3
UW30 Dimensions
U.S.A. and Canada only. For customer orders, contact the Customer Service department at 800/392‑3497 Fax:
For warranty repair or service information, contact the Service Repair department at
For technical assistance, contact Technical Support at 866/78 AUDIO Please refer to the Engineering Data Sheet for warranty information.
Specifications subject to change without notice.
Part Number 38109‑847 Rev C