Gas Slide-In Cooktop
E36GC76GPS
36" min.
35 7/8"
13" 
2" max. 
cabinet depth
25"
30" min. for
unprotected cabinet
18"
min. 24" min. with protected bottom
surface
Optional 9" stainless steel backsplash (attaches to wall)
Side inset 5/8"
1" min. recommended distance between rear edge of cutout and nearest combustible surface above countertop 
3" 
2" dia. 
opening to route power cable
22 1/8"
11/8" 24" max.
1" countertop 
overhang
3515/16" ** |
|
| ||
|
| 2" |
| |
2 | 1/2" | Support |
| |
platform | 351/8" | |||
|
| |||
4" x 4" opening to route gas supply
7 1/2"
7 3/4"
**Applies only in case of countertop backwall
7" min. to nearest combustible wall (either side of unit)
3/8"
7 1/4"
35 3/16" * 3515/16" *
*Both cutout dimensions are critical to proper cooktop installation.
Due to variations in countertop materials it is recommended to undercut finished dimension 3515/16" and adjust upon installation of cooktop.
36" Gas Slide-In Cooktop Specifications
•Product Weight – 115 Lbs.
•Voltage Rating – 120V/ 60Hz/15 Amp
•Connected Load (kW Rating) @120 Volts = 0.001kW (For use on adequately wired 120V, dedicated circuit having
•Amps @120 Volts = 0.008 Amps
•Always consult local and/or national electric and gas codes.
•Cooktop ships with 3/4" factory regulator.
•LP Gas conversion kit supplied.
•Plan installation to have electrical connection, gas shutoff valve, and pressure regulator accessible from front of cabinet. Locate 120V grounded outlet in a 4"W x 5"H area on rear wall, 16" above floor, aligned center with cooktop.
•Cabinet and/or countertop must completely enclose recessed portion of cooktop. Respect cutout dimensions and clearances and ensure that all contact surfaces are solid and level.
•Overhead cabinetry should not exceed a 13" maximum depth.
•Allow 30" minimum clearance between top of cooktop and bottom of unprotected wood or metal overhead cabinetry.
•Absolute minimum horizontal distance between overhead cabinets installed to either side of appliance must be no less than maximum width of appliance.
•Allow 24" minimum clearance when bottom of wood or metal overhead cabinet is protected by not less than 1/8"
Electrolux Major Appliances, N.A.
•Allow 1" minimum clearance between rear edge of cooktop and nearest combustible surface above countertop. If required clearance can not be maintained, then optional stainless steel backsplash or noncombustible backsplash material must be used – otherwise installation will require custom cabinet and countertop dimensions.
•Allow 7" minimum clearance from edge of cooktop to nearest combustible wall on either side of unit.
•It is recommended that drawers not be used beneath cooktop.
•To reduce risk of fire when using overhead cabinetry, install vent hood that projects horizontally a recommended minimum of 7" beyond bottom of cabinets.
•Gas
•Gas
36” Downdraft Vent. (Refer to
Note: For planning purposes only. Refer to Product Installation Guide on the web at electroluxicon.com for detailed instructions.
Optional Accessories
•When replacing an existing cooktop with countertop cutout deeper
than
• 9" Stainless Steel Backsplash – (PN#
• Black Knobs Kit – (PN#
USA • 250 Bobby Jones Expressway • Augusta, GA 30907 • | High standards of quality at Electrolux Home Products, Inc. mean we are |
CANADA • 5855 Terry Fox Way • Mississauga, ON L5V 3E4 • | constantly working to improve our products. We reserve the right to change |
specifications or discontinue models without notice. |
E36GC76GPS 01/09 | © 2009 Electrolux Home Products, Inc. | Printed in the U.S.A. |