Specifications

P2000

Precision SeriesTM

Power Amplifier

• 560 watts per channel

at 8 ohms, 900 watts per

channel at 4 ohms, 1,200

watts per channel at 2 ohms

• Neutrik Speakon® output

connectors allow use of

heavy-gauge speaker wire

for low-loss connections

• Extremely low (<0.01%)

dynamic distortion ensures

excellent sound quality

• Three-year parts-and-labor

warranty

Voltage Gain, 1 kHz, Any Mode, Constant-

Load Protection:

Conditions:

Gain Option:1

Start-up/shutdown transients; dc fault;

1. 0 dBu = 0.775 V rms.

26 dB

infrasonic signals; low ac line voltage;

2. Dual-mode ratings are for each channel,

Input Sensitivity, 1 kHz, Dual Mode for

nonlinear signal limiter

both operating, unless noted.

800 Watts into 4 Ohms:

Output Topology:

3. 120-volt ac line voltage maintained

0 dBu (775 mV)

True complementary symmetry with

throughout testing.

Maximum Input Level (reference 1 kHz):

ungrounded collectors (no mica insulators

Continuous Rated Output Power (20-

+20 dBu (7.75 V)

means better heat transfer)

20,000 Hz at less than 0.1% THD, both

Input Impedance (per channel,

Output Devices,

channels driven per EIA RS-490),

20-20,000 Hz), Balanced:

Total Number: 32 devices

Dual Mode, 2 Ohms:

20 kilohms

Pd(max) Rating: 250 watts

1,000 watts

Phase Response (at rated power, any

Ic (collector current): 20 amps dc

Bridged Mode, 4 Ohms:

mode, 10-30,000 Hz):

Tj(max): 200 °C (392 °F)

2,000 watts

± 22.5 degrees

Controls and Switches,

Dual Mode, 4 Ohms:

THD Plus Noise at 1 kHz (at rated power,

Rear:

800 watts

measurement bandwidth 80 kHz):

Hi-Lo-Cut Filter(On/Off); Bridged Mode

Bridged Mode, 8 Ohms:

<0.01%

switch (Bridged/Normal); Limiter mode

1,600 watts

IMD (SMPTE) (60 Hz/7 kHz, typical, at

(Fast/Slow); Circuit ⊥ To Chassis

Dual Mode, 8 Ohms:

rated power; see Figure 2):

Switch (Grounded/Ungrounded); Input

500 watts

<0.01%

Routing (Parallel Mono or Dual Stereo)

Continuous Rated Output Power (1 kHz,

DIM 30 (composite square-sine wave

Front:

1% THD, both channels driven per EIA

band-limited to 30,000 Hz):

Two calibrated input level controls;

RS-490),

<0.01%

power switch

Dual Mode, 2 Ohms:

DIM 100 (composite square-sine wave

Front-Panel Indicators:

1,200 watts

band-limited to 100,000 Hz):

Five LED’s per channel (10 total) for power

Bridged Mode, 4 Ohms:

<0.01%

on, input signal, output signal, limiter

2,400 watts

Rise Time (10% to 90% at rated power,

on and protect on

Dual Mode, 4 Ohms:

any mode):

Connections,

900 watts

<2.5 microseconds

Input:

Bridged Mode, 8 Ohms:

Slew Rate, Any Mode:

3-pin female XLR-type connectors for

1,800 watts

>35 V/microsecond

each channel in parallel with a 3-pin

Dual Mode, 8 Ohms:

Damping Factor, Any Mode:

male XLR-type output connector for

560 watts

>300

easy signal routing; the XLR connec-

Power Bandwidth (+0, –1 dB, reference

Amplifier Protection:

tors are wired according to the IEC 268

1 kHz), Any Mode, 4 Ohms:

Excessive output voltage; shorted loads;

standard: pin 1 shield, pin 2 positive,

10-30,000 Hz

excessive phase shift; rf interference;

pin 3 negative

Frequency Response

overtemperature; excessive back EMF;

Output:

(+0, –3 dB, reference 1 kHz/1 watt) :

In-rush current limiter

Neutrik Speakon® NL4MP for channels

<10-30,000 Hz

__________________

A, B and for bridged mode

1. Configured for constant-gain option, all Precision SeriesTM

Power:

amplifiers, regardless of power rating, have a maximum

12-gauge, 3-wire, permanently attached

voltage gain of 26 dB.

power cable; no ac plug supplied

Electro-Voice P2000 warranty Specifications

P2000

Power Amplifier

warranty

SPECIFICATIONS

Conditions:

Gain Option:1

800 Watts into 4 Ohms:

Output Topology:

Dual Mode, 8 Ohms:

rated power; see Figure 2):

Bridged Mode, 8 Ohms:

Slew Rate, Any Mode:

Dual Mode, 8 Ohms:

Damping Factor, Any Mode:

1 kHz), Any Mode, 4 Ohms:

(+0, –3 dB, reference 1 kHz/1 watt) :

Power:

P2000 specifications