Specifications

P1200

Precision SeriesTM

Power Amplifier

• 370 watts per channel at 8 ohms, 550 watts per channel at 4 ohms, 650 watts per channel at 2 ohms

• Compact, two-rack-space chassis

• Neutrik Speakon® output connectors allow use of heavy-gauge speaker wire for low-loss connections

• Three-year parts-and-labor warranty

SPECIFICATIONS	Frequency Response	Output Topology:
Conditions:	(–1 dB, reference 1 kHz/1 watt) :	True complementary symmetry with
1. 0 dBu = 0.775 V rms.	10-30,000 Hz	ungrounded collectors (no mica insulators
2. Dual-mode ratings are for each channel,	Voltage Gain, 1 kHz, Input Level Controls	means better heat transfer)
both operating, unless noted.	Full Clockwise, Constant-Gain Option:1	Output Devices,
3. 120-volt ac line voltage maintained	26 dB	Total Number: 20 devices
throughout testing.	Input Sensitivity, 1 kHz, Dual Mode for 550	Pd(max) Rating: 250 watts
Continuous Rated Output Power (20-	Watts into 4 Ohms:	Ic (collector current): 16 amps dc
20,000 Hz at less than 0.1% THD, both	0 dBu (775 mV)	Tj(max): 200 °C (392 °F)
channels driven per EIA RS-490),	Maximum Input Level (reference 1 kHz):	Controls and Switches,
Dual Mode, 2 Ohms:	+20 dBu (7.75 V)	Rear:
600 watts	Input Impedance (per channel,	Hi-Lo-Cut Filter(On/Off); Bridged Mode
Bridged Mode, 4 Ohms:	20-20,000 Hz), Balanced:	switch (Bridged/Normal); Limiter mode
1,200 watts	20 kilohms	(Fast/Slow); Circuit ⊥ To Chassis
Dual Mode, 4 Ohms:	Phase Response (at rated power, any	Switch (Grounded/Ungrounded); Input
500 watts	mode, 10-30,000 Hz):	Routing (Parallel Mono or Dual Stereo)
Bridged Mode, 8 Ohms:	±22.5 degrees	Front:
1,000 watts	THD Plus Noise at 1 kHz (at rated power,	Two calibrated input level controls;
Dual Mode, 8 Ohms:	measurement bandwidth 80 kHz):	power switch
350 watts	<0.01%	Front-Panel Indicators:
Continuous Rated Output Power (1 kHz,	IMD (SMPTE) (60 Hz/7 kHz, typical, at	Five LED’s per channel (10 total) for power
1% THD, both channels driven per EIA	rated power; see Figure 2):	on, input signal; output signal; limiter
RS-490),	<0.01%	on and protect on
Dual Mode, 2 Ohms:	Rise Time (10% to 90% at rated power,	Connections,
650 watts	any mode):	Input:
Bridged Mode, 4 Ohms:	<2.5 microseconds	3-pin female XLR-type connectors for
1,300 watts	Slew Rate, Any Mode:	each channel in parallel with a 3-pin
Dual Mode, 4 Ohms:	>30 V/microsecond	male XLR-type output connector for
550 watts	Damping Factor, Any Mode:	easy signal routing; the XLR connec-
Bridged Mode, 8 Ohms:	>300	tors are wired according to the IEC 268
1,100 watts	Amplifier Protection:	standard: pin 1 shield, pin 2 positive,
Dual Mode, 8 Ohms:	Excessive output voltage; shorted loads;	pin 3 negative
370 watts	excessive phase shift; rf interference;	Output:
Power Bandwidth	overtemperature; excessive back EMF;	Neutrik Speakon® NL4MP for channels
(+0/–1 dB, reference 1 kHz),	In-rush current limiter	A, B and for bridged mode
Dual Mode, 4 Ohms:	Load Protection:	Power:
20-20,000 Hz	Start-up/shutdown transients; dc fault;	14-gauge, 3-wire, permanently attached
Bridged Mode, 8 Ohms:	infrasonic signals; low ac line voltage;	power cable;
20-20,000 Hz	nonlinear signal limiter	Operating Voltage:
Dual Mode, 8 Ohms:	__________________	120 V, 60 Hz ac
Dual Mode, 8 Ohms:	1. Configured for constant-gain option, all Precision SeriesTM	120 V, 60 Hz ac
20-20,000 Hz
20-20,000 Hz	amplifiers, regardless of power rating, have a maximum
	amplifiers, regardless of power rating, have a maximum
	voltage gain of 26 dB.

P1200 specifications

The Electro-Voice P1200 is a standout performer in the world of professional audio, designed primarily for PA systems and live sound applications. Renowned for its exceptional sound quality and reliability, the P1200 is well-suited for both venues and portable sound setups. Its robust design and advanced features make it a favorite among sound engineers and musicians alike.

One of the main features of the P1200 is its impressive power output. With an RMS output of 1200 watts, it delivers clear and powerful sound, making it capable of driving a range of speakers with ease. This power is supplied through its high-efficiency Class D amplifier, which not only ensures minimal distortion but also enhances performance with improved heat management. This means that users can push the P1200 to high volumes without fear of overheating, ensuring consistent performance throughout any event.

The P1200 also incorporates cutting-edge digital signal processing (DSP) technology. This technology allows for precise control over audio signals, enabling users to shape their sound with various EQ settings and crossover options. The built-in DSP enhances the overall audio experience by optimizing frequency response and ensuring that the output matches the requirements of the connected speakers. It also includes a range of presets tailored for different applications, making setup quick and straightforward.

In terms of connectivity, the Electro-Voice P1200 is versatile, featuring multiple input options. Users can connect to the amplifier via XLR or 1/4-inch inputs, accommodating various audio sources, from microphones to instruments. Additionally, the unit includes outputs for linking to other amplifiers or processing units, ensuring seamless integration into existing sound systems.

Durability is another key characteristic of the P1200. It features a rugged steel chassis designed to withstand the rigors of touring and live performances. The front panel includes intuitive controls and a clear LED indicator, simplifying operation for users during dynamic environments.

In conclusion, the Electro-Voice P1200 is a powerful, efficient, and versatile amplifier that caters to the needs of professional audio applications. With its robust construction, high output capability, and advanced DSP technology, it promises reliability and superb sound quality, making it an excellent choice for both live sound and permanent installations.