Electro-Voice ZX1iSeries Dimension Drawings Architectural and Engineering Specs, Block Diagrams

Page 4

Dimension Drawings:

 

Architectural and Engineering Specs:

 

 

The loudspeaker shall be a two-way system consisting of one 8"” (102mm) low-

 

 

frequency transducer, 1" (25mm) high-frequency true compression driver with rotatable

 

 

horn, and frequency dividing network installed in a vented enclosure. The network

 

 

shall include a passive limiter for both the low frequency and high frequency

 

 

transducers. The high frequency compression transducer shall drive a horn to evenly

 

 

cover a pattern of either 90° by 50° or 100° by 100°. The horn shall be rotatable to

 

 

allow for horizontal or vertical mounting of the cabinet. The enclosure shall be molded

 

 

of high impact polystyrene.

Top View

 

The finish shall be a paintable black or white. The grille shall be zinc plated, powder

 

coated for corrosion resistance, and equipped with both hydrophobic cloth and acoustic

 

 

foam. The loudspeaker position shall be adjustable over a range of 100° horizontally

 

 

and 45° vertically.

 

 

The support bracket shall be low profile and integral with the enclosure. The bracket

 

 

shall allow for a quick snap fit mounting of the speaker enclosure for placement

 

 

before securing. The speaker terminals shall include a 4 pin removable phoenix style

 

 

connector to allow for signal pass through. The system shall be weather resistant to

 

 

MIL Spec 810 and IEC 529 test conditions.

 

 

The loudspeaker shall be available with a 100w transformer for 70 or 100v operation.

 

 

The speaker shall have ASCTM for transformer saturation protection against overload.

 

 

Their also shall be an 8 ohm bypass position on the wattage selector switch to enable

 

 

8 ohm operation from these models.

 

 

The loudspeaker system shall meet the following performance criteria: Power handling,

 

 

200-Watts long term program using IEC268-5 shaped pink noise; Frequency response,

 

 

48 Hz – 20 kHz (-10 dB from rated sensitivity); Pressure sensitivity, 94 dB at one

 

 

watt, 60 Hz – 20 kHz at one meter; Impedance, 8 ohms nominal, 6 ohms minimum.

 

 

The enclosure shall be 17.75" (451mm) high, 11.12" (282mm) wide, 10.35" (263mm)

 

 

deep. Net weight shall be 18.5 lbs (8.4 kg) for non-transformer versions and 23.0 lbs

Front View

Right View

(10.4 kg) for transformer versions.

Block Diagrams:

 

 

ZX1i (Non-Transformer) and ZX1i-100T in 8Ohm Mode

ZX1i-100T

CAUTION

This ZX1i Loudspeaker should be suspended overhead only in accordance with the procedures and limitations specified in the ZX1 Users Manual and possible manual update notices. This system should be suspended with certified rigging hardware by an authorized rigging professional and in compliance with local, state, and federal overhead suspension ordinances.

ZX1iPart Numbers

301851-001 - ZX1i-90, 90° x 50° Horn, Black Finish

301851-002 - ZX1i-90W, 90° x 50° Horn, White Finish

301851-003 - ZX1i-100, 100° x 100° Horn, Black Finish

301851-004 - ZX1i-100W, 100° x 100° Horn, White Finish

301852-001 - ZX1i-100T, 100° x 100° Horn, Black Finish, Transformer

301852-002 - ZX1i-100TW, 100° x 100° Horn, White Finish, Transformer

PerformanceMatch

D170180 CPS2T, 120V Power Amplifier, 2 x 600W

D170261 CPS2.8, 120V Power Amplifier, 2 x 800W

Accessories

301918-001 AB-ZX1i, Array Bracket Kit for 2 or 4 Systems, Black

12000 Portland Avenue South, Burnsville, MN 55337 Phone: 952/884-4051, Fax: 952/884-0043

www.electrovoice.com

© Telex Communications, Inc. 5/2005

Part Number 38110-470 Rev. 1

U.S.A. and Canada only. For customer orders, contact Customer Service at:

800/392-3497 Fax: 800/955-6831 Europe, Africa, and Middle East only. For customer orders, contact Customer Service at:

+ 49 9421-706 0 Fax: + 49 9421-706 265 Other International locations. For customer orders, contact Customer Service at:

+ 1 952 884-4051 Fax: + 1 952 736-4212 For warranty repair or service information, contact the Service Repair department at:

800/685-2606 For technical assistance, contact Technical Support at: 866/78AUDIO

Specifications subject to change without notice.

Image 4
Contents Technical Specifications General DescriptionZX1i Series Full Range Loudspeaker ZX1i-90ZX1i-100 Frequency Response & ImpedanceHorizontal 1/3 Octave Engineering Data SheetPolars, ZX1i-90 Polars, ZX1i-100 Dimension Drawings Architectural and Engineering Specs Block Diagrams

ZX1iSeries specifications

The Electro-Voice ZX1i Series represents a dynamic advancement in compact loudspeaker technology, designed to deliver exceptional audio performance in a range of environments. These speakers are particularly suited for venues that require high-quality sound reinforcement, such as small to medium-sized spaces, theaters, and corporate events. The main feature of the ZX1i series is its powerful and precise sound delivery, making it an ideal choice for both live sound and installed applications.

One of the standout characteristics of the ZX1i speakers is their robust, weather-resistant design, which allows them to perform reliably in outdoor settings. This is facilitated by the use of a high-quality polypropylene enclosure that minimizes resonance and allows for clear audio reproduction. The speaker also features a water-resistant grille, ensuring durability against environmental elements.

The ZX1i Series includes high-performance transducers that optimize sound quality across different frequencies. The 8-inch woofer delivers rich, full-bodied bass, while the 1-inch compression driver provides crisp and articulate highs. This combination results in a well-balanced sound profile that is perfect for music playback and vocal clarity, making it versatile for various sound reinforcement applications.

Another notable feature is the innovative waveguide design integrated into the ZX1i series. This design enhances the speaker’s dispersion characteristics, ensuring that sound is evenly distributed across the listening area. As a result, audiences can enjoy consistent audio quality regardless of their position in the space.

Additionally, the ZX1i speakers are equipped with multiple mounting options, including stand and bracket mounts, making them easy to integrate into different setups. Their lightweight construction further simplifies transportation and installation, enabling quick setup for events.

The Electro-Voice ZX1i Series stands out due to its blend of thoughtful engineering, versatile application, and remarkable sound fidelity, making it a top choice for audio professionals who demand quality and reliability in their sound systems. Whether used for public speaking, music performance, or ambient sound, the ZX1i series consistently delivers a premium auditory experience suitable for diverse environments.