Cuisinart CSB-55 manual Chopper Grinder Parts and Assembly, Wall Mount Option

Page 7

The counter storage unit can be placed in a cupboard or on a shelf if not on the counter.

Wall Mount Option

Separate the two plastic storage stand pieces. You will need only one for wall mount. (See diagrams below). The unit you must use is the section that has the round storage hole to hold the whipping disk.

Wall Anchor

Anchor Bolt

When selecting a mounting location, be sure to leave enough room above the storage stand for your hand to remove the SmartStick™ Hand Blender. Also be sure to leave enough room below the stand to allow the appliance to hang freely.

You will need to drill two holes 2 5/8" apart from each other, measured from the center of each hole. To assist in proper location of holes for the mounting screws, remove the wall mount template from this instruction book. Place the template over the back of the wall unit, aligning the outline of the template with the wall bracket. When you have done this, place the template and wall bracket against the wall in the desired location. Remove the wall bracket, leaving the template in place. Mark the wall with a pencil in the locations for screw holes indicated by the template. Remove the template.

With a drill, make a 3/16" starter hole for each screw. Place the plastic anchor in each hole. Push completely into the hole with fingers, or tap in gently with a hammer. Screw a mounting screw into each hole leaving 1/8" to 1/4" of the head and screw exposed.

Position the two mounting holes of the wall bracket over the screw heads and slide wall bracket down the wall until the bracket is resting against the screw head, and will not slide any further. If the wall bracket feels too

loose against the wall, remove bracket, put screws further into wall and replace bracket.

SmartStick

Place the assembled SmartStick™ Hand Blender into the wall bracket. The unit will hang from the bracket, held in place by the motor body width.

To reduce the risk of fire or electric shock, do not operate any heating appliance beneath the mounting unit.

Do not mount the storage bracket/ unit over or near any portion of a heating or cooking appliance or a sink or basin.

Mini Chopper Grinder Storage.

The SmartStick™ Mini Prep® Chopper Grinder Attachment stores neatly on the countertop in a minimum of space. Store the unit assembled to prevent loss of parts. Store the blades as you would sharp knives—out of reach of children.

Chopper Grinder Parts and Assembly

 

 

 

E

F

A. Chopper Grinder

 

 

F

 

 

G

 

Prep Bowl

 

 

 

 

B. Cover Slots (3)

 

 

 

 

 

 

 

 

 

 

for Attaching

N

L

M

G

 

Cover

 

C. Metal Blade

 

 

K

 

 

Assembly Shaft

 

 

 

 

 

D. Rubber Feet

 

 

 

 

 

E. Blade Assembly

 

 

J

 

 

F. Blade Ring

 

 

 

 

G. Plastic Blade

 

 

H

E

 

Sheath

 

MINI PREP

 

H. Chopper Grinder

 

SmartStick

 

 

 

 

 

Chopper Grinder Attachment

I

 

 

Cover

 

B

 

 

 

G

 

I. Lift Tabs

 

 

 

 

 

 

 

 

 

 

 

J. Chopper Grinder

 

 

 

 

 

 

 

 

 

 

Spline

 

A

C

 

 

K. Central Hub

 

F

 

Holding Ribs

 

 

 

 

 

 

 

L. Curved Sharp

 

 

 

 

 

 

 

 

 

 

Edge

 

D

 

 

 

M. Flat Blunt Edge

 

 

 

 

N. Ridges for

 

 

 

 

 

Gripping

 

 

 

SmartStick

 

 

 

 

SmartStick

 

 

 

 

 

MINI PREP

 

 

 

 

 

Chopper Grinder Attachment

SmartStick

 

 

Reversible Blade.

The Cuisinart SmartStick™ Mini Prep® Chopper Grinder attachment is equipped with a reversible blade. This blade is sharp on one side and blunt on the other. The blade is attached to a plastic ring which slides over the blade assembly shaft, so it can be easily turned over to select the appropriate blade. A guide for proper blade selection follows in the section, Chopper Grinder Tips for Processing Foods.

Before you process any food, assemble the parts.

1.Place the Prep Bowl on a flat, dry, stable surface. It should be close to an electrical outlet of the same voltage as stated on the rating plate on the SmartStick™ Hand Blender.

12

13

Image 7
Contents Instruction Booklet Introduction Table of ContentsFeatures and Benefits Making the Shaft Longer Hand Blender AssemblyShaft Length Adjustment Before YOU BeginHelpful Hints Hand Blender OperationBlending & Mixing AttachmentsStorage Stand / Wall Brackets Countertop OptionWall Mount Option Chopper Grinder Parts and AssemblyNotch Processing Food Chopper Grinder Tips forPreparing the Food Operating Techniques Processing FoodIngredient Comments Recipe Suggestions CleaningSmartstick Hand Blender SmartStick Mini Prep Chopper Grinder AttachmentFresh Tomato Zucchini Bisque Beverages Whip cream to a fluffy consistency in seconds DessertsIB-3028D

CSB-55 specifications

The Cuisinart CSB-55 Smart Stick Hand Blender is a versatile kitchen tool designed to simplify food preparation while delivering outstanding results. Combining power with ease of use, this immersion blender is ideal for those who love to cook and entertain.

One of the standout features of the CSB-55 is its powerful 200-watt motor, which effortlessly blends, purees, and emulsifies a variety of ingredients. Whether you are making soups, sauces, or smoothies, the robust motor ensures consistent results every time. This immersion blender also boasts a patented ergonomic grip that makes it comfortable to hold, allowing for extended use without fatigue.

The CSB-55 is equipped with a 2-speed slide control, providing you with the flexibility to adapt your blending speed based on your specific needs. The low speed is perfect for gentle blending, while the high speed is great for achieving a smooth and creamy texture. This level of control is particularly beneficial when working with delicate ingredients or when you want to avoid over-processing.

Another key feature of the Cuisinart CSB-55 is its stainless steel blending shaft, which not only adds durability but also ensures that the blender can easily handle hot liquids. The blending shaft is removable, making it easy to clean and maintain after use. The dishwasher-safe parts are an added bonus, simplifying the cleaning process significantly.

The blender also includes a blending cup, which is ideal for small batches or individual servings. With measurement marks on the cup, users can conveniently prepare ingredients without needing extra measuring tools.

Additionally, the CSB-55 is designed with safety in mind. It features a locking mechanism that ensures the metal blend shaft is securely attached during use, preventing accidental detachment.

In terms of design, the Cuisinart CSB-55 is sleek and modern, available in various colors to match your kitchen decor. Its compact size makes it easy to store, saving valuable counter space.

In summary, the Cuisinart CSB-55 Smart Stick Hand Blender combines power, versatility, and convenience, making it a must-have for any home chef. With its powerful motor, ergonomic design, and easy-to-clean features, this immersion blender is perfect for anyone looking to enhance their cooking experience. Whether for everyday meals or special occasions, the CSB-55 stands out as a reliable and efficient kitchen companion.