Clarion APX401.4 installation manual Final System Checks, Troubleshooting

Page 14

4 Channel Power System Amplifier

FINAL SYSTEM CHECKS

1.Start the engine and turn on the source unit. After a two-second delay, slowly increase the Volume Control and listen to the audio. If you hear any noise, static, distortion or no sound at all, check the connections, and also refer to Troubleshooting. Depending on your system design, the levels may become quite loud even at low Volume Control settings. Until you get an “audio feel” of the system’s power, use care when adjusting controls.

2.Turn the Balance Controls to their extreme positions and listen to the results. Audio output should match control settings (audio from the left speaker when balance is left).

3.Increase the volume and verify that the amplifier reproduces audio (at full frequencies) without distortion. If you hear distortion, check the connections and verify that the Gain Control is set correctly. Another possibility is damaged speakers or under-powered speakers. Once again refer to Troubleshooting for additional help.

TROUBLESHOOTING

Problem

No Audio.

Solution

Low or no remote turn-on voltage. Check remote connections at amplifier and source unit.

Blown amplifier fuse. Replace with new fast-blow fuse (same rating).

Power wires not connected. Check battery and ground wiring at amplifier; also check battery connections.

Speaker leads shorted. Check speaker continuity to ground, it should not show a common ground.

Speakers not connected or are blown. Check speaker connections at amplifier, measure coil impedance.

Problem

Audio cycles on and off.

Solution

Thermal protection circuits are shutting amplifier off. Check location for adequate ventilation; consult an authorized Clarion Audio Dealer.

Problem

Distorted audio.

Solution

Gain is not set properly, or damaged speaker cones. Review Setting Gain; inspect each speaker cone for signs of damage (i.e. frozen cone, burning smell, etc.)

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents E R a T IO N in S T a L L a T IO N M a N U a L Introduction Table of ContentsAbout the Manual and Warranty Description Input Connections and Audio ControlHigh-pass/Low-pass Filter Controls Connections for Power and Speakers Applications Channel Stereo System Channel High-Pass, 2-Channel Low-Pass Channel Stereo System with Low-Pass Bridged Mono Channel Channel High Power System Satellite or Subwoofer Mixed-Mode System On Rear Full-Range Speakers On Front Wiring Precautions InstallationMounting Precautions Electrical connections for the APX401.4 Setting the Bass Boost Setting the GainSetting the Crossover Troubleshooting Final System ChecksProduct Specs THDWarranty Information

APX401.4 specifications

The Clarion APX401.4 is an excellent addition to any audio enthusiast’s collection, designed to deliver superior sound quality and performance in a compact format. This four-channel amplifier is engineered to enhance your car audio system with crystal clear sound and powerful output, making it a popular choice among novice and seasoned users alike.

One of the standout features of the APX401.4 is its robust power output. It is capable of delivering 50 watts RMS per channel at 4 ohms, with the potential to drive up to 100 watts RMS per channel at 2 ohms. This flexibility allows users to connect a variety of speakers and subwoofers to suit their audio preferences, whether they are looking for deep bass or crisp highs.

The amplifier utilizes a Class AB design, which is well-known for its efficiency and sound quality. This design offers the best of both worlds—providing high levels of power while minimizing distortion. The result is a clean and rich audio experience, making it ideal for those who appreciate detailed sound reproduction across a range of frequencies.

Additionally, the APX401.4 incorporates advanced technologies such as a high-level input feature, allowing for direct connection to factory-installed head units that do not have preamp outputs. This makes it accessible for installation in various vehicles without the need for significant upgrades to the existing audio system.

The amplifier also comes equipped with an adjustable low-pass filter and a high-pass filter. This feature enables users to tailor the crossover frequencies to achieve a more precise sound profile based on their specific speakers and listening preferences. Whether you want to eliminate unwanted distortion from higher frequencies or enhance bass response, this amplifier provides the necessary tools to fine-tune your audio output.

For those concerned with durability and longevity, the Clarion APX401.4 is built with high-quality components and a robust chassis design that can withstand the rigors of automotive environments. Its compact size allows for easy installation in a variety of spaces within the vehicle.

In summary, the Clarion APX401.4 is a powerful, efficient, and flexible four-channel amplifier that enhances any car audio setup. With its impressive power capabilities, advanced technology, and user-friendly features, it’s an outstanding choice for anyone looking to elevate their in-car listening experience.
Top Page Image Contents