KitchenAid KSFS25FKBL00 Installation Information, Leveling the Refrigerator, Base Grille Removal

Page 13

INSTALLATION INFORMATION

LEVELING THE REFRIGERATOR

IMPORTANT: All four leveling legs must con- tact the floor to support and stabilize the full weight of the refrigerator.

Base Grille Removal

1.Open the refrigerator doors.

NOTE: Do not remove the Tech Sheets fas- tened behind the grille.

2.Remove the screws from the base grille and remove the grille.

Adjusting The Rollers

The roller adjusting bolts are located behind the base grille. The refrigerator has four adjust- able rollers: two in front, and two in the rear.

There are two sets of roller adjusting bolts found at the base of the refrigerator on each side. The rear leveling bolt (1) is yellow, and the front leveling bolt (2) is silver.

1

2

NOTE: Be careful not to unscrew the leveling bolts too much when lowering the refrigerator. The bolt head will start to come away from the refrigerator when it is in the lowest position. If the bolt comes out of the rear roller bracket, the compartment access cover on the back of the refrigerator will have to be removed to reinstall the bolt.

1.Use a 1/2″ (12.70 mm) socket wrench to adjust the leveling bolts. Turn the leveling bolt to the right to raise that side of the refrigerator, or turn the leveling bolt to the left to lower that side. It may take several turns of the leveling bolts to adjust the tilt of the refrigerator.

2.Adjust the front leveling bolt so that the top of the refrigerator is parallel with the cabi- net above the refrigerator.

For standard cabinets, leave approximately 1/8″ (3.18 mm) gap between the top hinges and the cabinet.

For full-overlay cabinets, leave a 1/4″ (6.35 mm) gap for leveling.

If you do not have a cabinet above the refrigerator, adjust the refrigerator to make it level.

Cabinet

Front Of

Refrigerator

3.Adjust the rear leveling bolt and level the refrigerator with the side cabinets, or with the cabinet end panels.

4.If needed, use the four leveling bolts to raise the refrigerator to close the gap between the refrigerator top hinge, and the cabinet opening. Check to make sure that all four rollers still touch the floor, and that the cabinet doors above the refrigera- tor open all the way.

2-1

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Model Goals and Objectives ForwardTable of Contents Wiring Diagrams & Strip Circuits Electrical Power Supply & Grounding Requirements Safety FirstGeneral Electrostatic Discharge ESD Sensitive Electronics Model Number Model & Serial Number DesignationsSerial Number Model & Serial Number Label Tech Sheet Locations KSBP25FKSS KSBS25FKBL KSBS25FKBT SpecificationsKSFS25FKBT KSFS25FKWH KitchenAid will not pay for Refrigerator WarrantyPage Adjusting The Rollers Installation InformationLeveling the Refrigerator Base Grille RemovalPage Overview Theory of OperationFreezer Temperature Control Temperature Increasing Temperature ControlFreezer Temperature Control Temperature Decreasing Refrigerator Temperature Control Temperature IncreasingCompressor Evaporator FAN AIR Door DelayCompressor Protection Evaporator FAN MotorFailure Defaults Power InterruptionAdaptive Defrost Pulsed DefrostAIR Circulation Electronic Control Thermal ShutoffFreezer Thermistor KeypadPage Component Locations Component AccessLight Shield To remove the motorized air door Removing a Thermistor Removing a Door Switch Removing a Light Socket On the next Removing the Water ReservoirUnit Compartment Cover To remove the ice maker Removing the ICE Maker Auger Motor & CRUSH/CUBE SolenoidTo remove the auger motor or crush/ cube solenoid On the next To remove the evaporator fan motor To remove the defrost heater To remove the bimetalTo remove the evaporator Reassembly NotesRemoving the Condenser FAN Motor Removing the Compressor Removing the Inverter Assembly Removing the Main Control Board Assembly Electrical Shock Hazard Removing the Water Dispenser Fill Tube Wire Connectors & Ground Wire Removing the Water Valve To remove a door handle Removing the Freezer Door Handles & Freezer DoorTo remove the freezer door Disconnect the dispenser power con- nector Removing a Roller Page Thermistor Component TestingCondenser FAN Motor Voltages Compressor & InverterDefrost Heater & Bimetal Motorized AIR Door10 9 8 7 3 2 Main Control BoardICE Maker Auger Motor CRUSH/CUBE SolenoidWater Valve Solenoid Door SwitchPRE-DIAGNOSTICS Checks Diagnosis & TroubleshootingDiagnostics Mode To enter the diagnostics modeTesting The Dispenser Valve Input Diagnostics ChartTesting The Ice Maker Valve Input Water Filter Input WFI TestProblem Possible Cause Test PROCEDURE-ACTION Troubleshooting ChartPage Wiring Diagram Wiring Diagrams & Strip CircuitsCooling Circuits Strip CircuitsCompressor Condenser Fan MotorDefrost Heater Defrost CyclePage Product Specifications Warranty Information Sources

KSFS25FKBT00, KSFS25FKWH00, KSBS25FKBL00, KSBS25FKBT00, KSBS25FKWH00 specifications

The KitchenAid appliances KSCS25FKSS00, KSFS25FKBL00, KSBP25FKSS00, KSBS25FKWH00, and KSBS25FKBT00 represent a blend of innovative technology and elegant design, catering to the needs of modern kitchens. Each of these models brings unique features and functionalities that enhance convenience, efficiency, and style.

The KSCS25FKSS00 refrigerator is known for its spacious interior and flexible storage solutions. It includes adjustable shelves and a fresh-seal crisper that keeps fruits and vegetables fresher for longer. The exterior has a sleek stainless-steel finish that not only looks great but is also resistant to fingerprints, making cleaning a breeze.

Moving to the KSFS25FKBL00, this model emphasizes energy efficiency, showcasing Energy Star certification. A standout feature is its ice and water dispenser, providing easy access to chilled water and ice without opening the fridge. The temperature management system ensures that food stays at optimal temperatures, which helps in preserving the flavors and nutrients.

The KSBP25FKSS00, a powerful blender, is designed to meet the demands of diverse culinary tasks. With its high-performance motor and multiple speed settings, it easily blends, pulses, and crushes a variety of ingredients. The patented diamond blending system ensures consistent results, while the sleek design and sturdy base offer stability during operation.

The KSBS25FKWH00 and KSBS25FKBT00 models are side-by-side refrigerators featuring advanced cooling technologies. The Even-Heat temperature management system evenly distributes cold air, preventing warm spots and maintaining an ideal environment for storing perishables. The intuitive control panel allows users to adjust settings with ease, while bright LED lighting illuminates the interior, making it easy to see contents.

Both KSBS25FKWH00 and KSBS25FKBT00 come equipped with ample door storage and a separate dedicated space for deli meats, further enhancing organization within the fridge. Their stylish finish complements any kitchen style, offering a combination of functionality and aesthetic appeal.

Overall, the KitchenAid KSCS25FKSS00, KSFS25FKBL00, KSBP25FKSS00, KSBS25FKWH00, and KSBS25FKBT00 models demonstrate the brand’s commitment to innovation, quality, and efficient kitchen solutions. Whether you need refrigeration, blending, or both, these appliances offer an exceptional blend of features to enhance your culinary experience.
Top Page Image Contents