KitchenAid 2210725 manual Plug Refrigerator, Level refrigerator, Style 1 Screw-on grille

Page 6

Style 2

bulb

nut

(provided)

Push the bulb end of the tubing into the water valve as far as it will go. Slide the nut forward and finger tighten. Tighten nut two

(2) more turns with wrench.

Plug in

refrigerator.

grounded

outlet

7. Plug power supply cord into grounded outlet.

power supply cord

8.Move refrigerator into final position.

This refrigerator has 4 adjustable rollers (2 front and 2 rear). There are 2 sets of roller adjusting bolts found at the base of the refrigerator on each side. The yellow top bolt will adjust the rear roller and the silver bottom bolt will adjust the front roller.

rear

adjusting

bolt

(yellow)

front

adjusting

bolt

(silver)

10.Use a 1/2" socket wrench to turn the roller adjusting bolts. Turning the bolt clockwise will raise the refrigerator and counterclockwise will lower the refrigerator. (NOTE: Be careful not to back the roller bolts out of the roller brackets when lowering the refrigerator. The bolt head will start to back out toward you when the roller is in its lowest position. If the screw does come out of the rear roller bracket, the compartment access cover on the back of the refrigerator will have to be removed to reinstall the bolt back into the nut.)

13.If desired, the 4 rollers may now be raised to close the gap between the refrigerator top hinge and the cabinet opening. Check that all 4 rollers contact the floor and the cabinet doors above the refrigerator open fully.

3/4" (19 mm) clearance set for

full-overlay cabinetcabinet doors and

refrigerator trim kit

NOTE: Cabinets with full-overlay doors will require 1/4" (6 mm) additional clearance between the top hinge and cabinet to prevent the doors from hitting the hinge when opening. (If you have a trim/panel kit on the refrigerator doors, 3/4" (19 mm) additional clearance will be required to prevent the cabinet doors from interfering with the refrigerator door trims.)

14.Replace the base grille.

• Open the refrigerator doors to 90°.

Style 1: Screw-on grille

Level refrigerator.

9. Remove base grille if it is installed.

• Open the refrigerator doors to 90°.

Style 1: Screw-on grille

1/8" (3 mm) clearance for leveling refrigerator

1/4" (6 mm) clearance set for full-overlay cabinet doors

cabinet

•Place the grille in front of the base grille area.

•Use a Phillips screwdriver and guide the screws through the grille holes and into the screw clips located in the corner plates on each side of the opening. Tighten screws securely.

•Find pockets located about 4 inches

(10 cm) in from each end of grille. Use Phillips screwdriver to remove the screw found in each pocket.

Do Not remove the Tech Sheets fastened behind the grille.

Style 2: Snap-on grille

•Grasp the grille with both hands. Lift up and tilt the top of the grill toward you.

Do Not remove the Tech Sheets fastened behind the grille.

The roller adjusting bolts are located behind the base grille.

11.Adjust the front rollers to bring the refrigerator top parallel with the cabinet above the refrigerator; leave about 1/8"

(3 mm) gap between the refrigerator top hinge and the cabinet. (If you do not have a cabinet above the refrigerator, adjust to make the top level.)

12.Adjust the rear bolts to bring the refrigerator level with the side cabinets or cabinet end panels.

Style 2: Snap-on grille

•Place the grille lower clips into the holes in the refrigerator panel. Roll the grille up toward the refrigerator until it snaps into place.

Page 6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents 36 91.4 CM COUNTER-DEPTH Refrigerator Product dimensions Before You startDetail a Door swing dimensions Opening dimensionsMinimum built-in Water supply requirements Supply RequirementsElectrical requirements Volt, 60-Hz, AC-only, 15- orInstall refrigerator Installation StepsInstall new water line If required Connect water line To refrigeratorStyle 1 Screw-on grille Plug RefrigeratorLevel refrigerator Style 2 Snap-on grilleFull Panel Dimensions for Decorator PanelsParts that Must be ordered Decorator door panel kits Cabinet Color Kit NumberTroubleshooting list If you need ServiceCheck that the power supply cord is If refrigerator If you need91,4 CM 36 PO Réfrigérateur Méme Profondeur QUE LE Comptoir Votre sécurité et celle des autres, c’est très important Dimensions du produitAvant de Commencer Détail aEspace d’encastrement dimensions Dimensions pour l’ouverture des portesAlimentation électrique Contacter un électricien qualifié pour l’installationCircuits de Alimentation en eauÉtapes de ’installation Si nécessaire, installer la Canalisation d’eauInstallation de la canalisation d’eau Branchement du RéfrigérateurAplomb du réfrigérateur Dimensions des panneaux décoratifs Pièces àPanneau inférieur Entretien Téléphone dans le Guide d’utilisation et entretien

2210725 specifications

The KitchenAid 2210725 is an essential tool for any kitchen enthusiast, bringing together versatile features, advanced technologies, and user-friendly characteristics that cater to both novice and experienced cooks. This versatile appliance stands out for its performance and reliability, designed to streamline various culinary tasks with ease.

At its core, the KitchenAid 2210725 boasts a powerful motor that ensures consistent and efficient performance for a wide array of cooking tasks. Whether you're mixing dough, whipping cream, or blending sauces, this machine can handle it all with remarkable precision. The motor is engineered to provide optimal torque, allowing for effective mixing without overheating, thus extending the lifespan of the unit.

One of the standout features of the KitchenAid 2210725 is its multi-functionality. This kitchen appliance is not limited to just mixing; with various attachments available, it bridges the gap between a stand mixer and a food processor. From kneading dough for bread to making pasta, the KitchenAid 2210725 can be equipped with additional accessories to transform into a versatile culinary workstation. This adaptability makes it a valuable investment for home cooks looking to explore new recipes.

The ergonomic design of the KitchenAid 2210725 also enhances user experience. The soft-grip handle ensures comfortable handling while the tilt-head design allows for easy access to the mixing bowl and attachments. This thoughtfully crafted design also makes it simple to add ingredients mid-mix, without the mess typically associated with traditional mixers.

Technology plays a crucial role in the efficiency of the KitchenAid 2210725. It is equipped with a slip-free bowl-lift design and a power hub that accepts over 15 different attachments, expanding its functionality. The appliance features multiple speed settings, granting users full control over mixing consistency, which is essential for creating everything from delicate meringues to robust pizza dough.

Furthermore, the KitchenAid 2210725 is designed with durability in mind. The robust construction materials ensure that it can withstand regular use without compromising performance. Its stylish finish also adds an aesthetic appeal, making it a welcome addition to any kitchen decor.

In conclusion, the KitchenAid 2210725 is a high-performance kitchen appliance that excels in versatility, power, and design. Whether you're a novice cook or a seasoned chef, this appliance promises to elevate your culinary skills and simplify your cooking process. Its combination of innovative technologies and user-centric features make it a staple in modern kitchens.
Top Page Image Contents