KitchenAid KWCU205H dimensions 30, 36 and 48 Wall-Mount Canopy Range Hood, Venting Requirements

® 30", 36" and 48" Wall-Mount Canopy Range Hood

PRODUCT MODEL NUMBERS

OVERALL DIMENSIONS

KWCU205H

KWCU265H

KWCU285H

Electrical: 120-volt, 60-Hz, AC-only, 15-amp. electrical supply. Use copper wire only. A time- delay fuse or circuit breaker and separate circuit is recommended.

VENTING REQUIREMENTS

Vertical roof venting		The vent system length should not
	roof cap	exceed the lengths shown in the
		chart below.
3-1/4" x 10"		Vent size	Maximum length
(8.3 cm x 25 cm)
		3-1/4" x 10"	35 ft. (10.7 m)
through the roof
		(8.3 cm x 25 cm)
Note:		7" (17.8 cm) round	40 ft. (12.2 m)
3-1/4" x 10"
(8.3 cm x 25 cm)		8" (20.3 cm) round	50 ft. (15.2 m)
rectangular vent

5-7/8"

(14.9 cm)

19-1/4"

(48.9 cm)

overall depth

10-7/8"

(27.6 cm)

1" (2.5 cm) min. - 20" (50.8 cm) max. upper chimney height

23" (58.4 cm) min. -

42" (106.7) max. 22" (58.9 cm) overall chimney

lower height chimney

height

9-1/2" (24.1 cm) canopy height

30" hood 29-15/16" (76 cm), 36" hood 35-3/8" (89.9 cm), 48" hood 47-1/4" (120 cm) overall width

must be used		9" (22.9 cm) round		60 ft. (18.3 m)
inside chimney
cover. Round
vent will not fit
inside chimney	To calculate the length of the system you need, add the
cover.
	equivalent feet for each vent piece used in the system.
	Vent Piece		3-1/4" x 10"		7" (17.8 cm),
			(8.3 cm x 25 cm)		8" (20.3 cm) or
			Rectangular		9" (22.9 cm) Round
	45° elbow		7.0 feet		2.5 feet
			(2.1 m)		(0.8 cm)
Horizontal wall venting
	90° elbow		5.0 feet		5.0 feet
			(1.5 m)		(1.5 m)

CABINET OPENING DIMENSIONS

19" (48.3 cm)*

13" (33 cm) cabinet

depth

3-1/4" x 10"		90° flat elbow	12.0 feet
(8.3 cm x 25 cm)			(3.7 m)
through the wall
		transition to round	5.0 feet
	wall		(1.5 m)
	cap
		wall cap	0.0 feet
			(0.0 m)

3-1/4" x 10" (8.3 cm x 25 cm)

vent system

30" hood 30" (76 cm),

36" hood 35-7/16" (90 cm) 48" hood 47-5/16" (120.2 cm) min. cabinet opening widths

18" (45.7 cm) min. clearance upper cabinet to countertop

24" (61 cm) min. bottom of canopy to cooking surface**

34-5/8"

(87.9 cm) min.

92-1/2"

(235 cm) min.

111-1/2"

(283.2 cm) max. ceiling to floor

Note: Flexible vent is Not recommended.

If it is used, each foot of flexible vent used is equivalent to two feet (61 cm) of straight metal vent when calculating the vent system length. (Example: A flexible elbow equals two standard elbows.)

3-1/4" x 10”			wall
(8.3 cm x 25 cm)
			cap
elbow
		6 ft. (1.8 m)
2 ft.	Maximum length			= 35		ft. (10.7 m)
(0.6 m)
	1 — 90° elbow			=	5	ft. (1.5 m)
	8 ft. (2.4 m) straight			=	8	ft. (2.4 m)
	1 — wall cap			=	0	ft. (0 m)
	Length of 3-1/4" x 10"
	(8.3 cm x 25 cm) system			= 13		ft. (4 m)

36" (91.4 cm) base cabinet height

*If the canopy hood is installed higher than 24" (61 cm) above the cooking surface, the middle bracket must be installed at the bottom point of the upper chimney sleeve.

**If the canopy hood is mounted higher than 24" (61 cm) above cooking surface, depending on ceiling height, upper chimney may need to be cut.

Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice.

Dimensions are for planning purposes only. For complete details, see Installation	Ref. 4360367 Rev. C
Instructions packed with product. Specifications subject to change without notice.	10-15-02