KitchenAid 4367501 Where local codes permit, Where local codes Do Not Permit

Electrical requirements

I

Eleclrlcal Shock Hazard

*Eleclrical ground Is required on lhls appliance.

-If cold waler pipe is inlerrupled by

plastic, non-metallic gaskets or other

insulating malerlals, Do Not use for grounding.

-Do No1 ground lo a gas pipe.

-Do Nol have a fuse in the newel or

grounding circuit. A fuse in the neulral

or grounding circuit could result in an electrical shock.

-Do Not use en extension cord with lhis appliance.

-Check	with		a qualified		electrician		if you
are	in doubt		as	to whether		the	appliance
is properly			grounded.
Failure	lo	lollow		lhese	Instructions		could
resull	in	serious		iniutv	or	dealh.

IIcodes permit end e separate grounding

wire is used. II is recommended that a

qualilied eleclrlcian determine that the

grounding path Is adequate.

IMPORTANT:

Save lnslallelion Inslruclions lor the local

electrical Inspector’s use.

El Thts appltance must be connected lo ’ the proper eleclncat vollage and

frequency spectfted on Ihe senatJraltnq plate The serrallralrng plale rs located on the frame behrnd the oven door

The branch circuit load lor a counler-mounted coaklop and nol more than two wall-mounted ovens, all supplred from a srngle branch crrcurt and localed rn Ihe same room. shall be compuled by addtng lhe nameplale ratmgs of the rndrvrdual appliances and lrealtng lhrs tolal

as equivalent lo one range

A three-wrre or four-we. srngle phase,

1201240-voll. 60-t+ AC-onlv eleclrrcat suoolr

(or three-wee or lourwre, 120/205-volt II ’ specrfred on the nameplate) IS requrred on a separate 30.ampere crrcu~t. fused on both srdes 01 the lkne A trme-delay fuse or crrcutt breaker 1s recommended

NOTE Wthng musl be modrfred lor 205.volt usage See “Connectrng to 205volt crrcurt.” Panel B

OVEN MUST BE CONNECTED

WITH COPPER WIRE ONLY.

ICIII IS the personal responsrbrlrty and ’ obtrgatron 01 Ihe customer lo contact

a qualrhed electricran lo assure that the electrical installation IS adequate and tn conformance wrlh the Natronal Electrrcal Code, ANSIINFPA 70.lalest edrtron.’ and all local codes and ordmances for the krtowan ratrng of the oven

Copres 01 the standards lksted may be oblarned lrom

‘National Fire Protection Associslion

Ballerymarch Park

Connecting lo 208~volt circuit

1 Remove access panel located on back ot OW”

2.Loosen Ihe f,rst and second screws I” the terminal block

3.Place metal jumper between Ihe llrsl and second screws

4.Trghten screws

5.Replace access panel

Electrical connection

Electrical Shock Hazard

. Electrical ground is required on this appliance.

-Do No1 connect lo the electrical supply until appliance is permanently

grounded.

. Disconnect power lo the junclion box before making the eleclricsl

connection.

-This appliance must be connecled lo a

grounded, metallic, permanent wiring

system. or a grounding connector should be connected lo the grounding terminal or wire lead on the appliance.

Failure lo do so could result in a ftre. personal injury or eleclrical shock

Tt 11sappliance 1s manufaclured wrth whrte (neulral) power supply wrre and a caBlnet- connected green groundrng we twtsled together Connecl Ihe appliance cable to the ~unclron box through Ihe U L -16184 condull COnneClOr Complete electrical connection according to local codes and ordrnances

A. Where local codes permit...

connecting the cabinel-grounding conductor

to the neulral (white) junction box wire:

B. Where local codes Do Not

permit...

connecting the cabinel-grounding conduclor lo the neutral (while) junclton box wire:

Ungrounded Neutral

1. Disconnect power supply.

2.Separate Ihe green and whrte appliance cable wires

3.Connect the whrte applrance cable ware to the neutral twhrlel wre I” Ihe ,unctron box.

4.Connect the two black wares together. then connect Ihe two red wares loaether See Fraure 2

5.Connect the green or bare groundrng we

from the applrance cable to a grounded we m the )unctron box

C. If connecting to a four-

wire electrical system...

Do Nol connect the cabinel-grounding

conduclor lo the neulral (while) junction box wire.

green wtres

Figure 3 _. __._

1. Disconnect power supply.

2.Separate the green and whrte appliance cable wires

3.Connect Ihe white appl~aw cable wre to the neutral (white) we in Ihe junctron box

4.Connecl the two black wrres lagether lhen connect the two red wes logelher See Figure 3

5.Connecl the green or bare groundrng we

from the appliance cable to the grounding we !n the lunct!on box

Quincy, Massachusells 02269

Thrs applrance should be connected drrectly to the lused drsconnect or crrcult

breaker box through Ilexrble. armored or non- metallfc sheathed, copper cable (wrth groundrng wire) Allow two to three leet of slack rn the lkne so that Ihe oven can be moved II servtcrng IS ever necessary Do Nol cut lhe conduil.

A U L -Isled condurl connector rt?usl be prowded at each end ot the power supply cable (al the applrance and at the ]unclron box) Wires s~zes (COPPER WIRE ONLY) and connectrons must conlorm wrth Ihe ralrng of Ihe appliance

Grounded Neulral

1.Drsconnecl the power supply.

2.Connecl together 3 w,res green and while appliance cable w,res and the neutra’ white ic~re I” Ile ,uncmn box

3.Connect Ihe two black wres together then connect the two red w,res logelher See Figure 1

Panel B