® 30" Freestanding and Slide-In Electric Range
PRODUCT MODEL NUMBERS
OVERALL DIMENSIONS
KERS807S
KESS908S
Freestanding Range
B
A
Electrical: When a
A
D* C
F
B*
maximum circuit protection is required), fused on both sides of the line. The model/serial number rating plate is located on the oven frame behind the storage drawer panel. A
F**
A.5³⁄₄" (14.6 cm)
B.30" (76.2 cm)
C.41³⁄₄" (106 cm) overall height with leveling legs screwed all the way in
D.36" (91.4 cm) cooktop trim height with leveling legs screwed all the way in*
G
E
E. 30" (76.2 cm)
F.27¹⁄₄" (69.2 cm) max. from handle to standoff at back of range**
G. Model/serial number plate (located on the
E**
A.30¹¹⁄₁₆" (77.6 cm)
B.35⁵⁄₈" (90.5 cm) height to underside of cooktop edge with leveling legs screwed all the way in*
C.Model/serial number plate (located on the
C
D
D30" (76.2 cm)
E. 27¼" (69.2 cm) from handle to standoff at back of range**
F.23" (58.4 cm) countertop notch to rear of cooktop
*Range can be raised approximately 1" (2.5 cm) by adjusting | *Range can be raised approximately 1" (2.5 cm) by adjusting |
the leveling legs. | the leveling legs. |
**When installed in a 24" (61 cm) base cabinet with 25" (63.5 cm) | **When installed in a 24" (61 cm) base cabinet with 25" (63.5 cm) |
countertop; front of oven door protrudes 1" (2.5 cm) beyond | countertop; front of oven door protrudes 1³⁄₄" (4.4 cm) beyond |
24" (61 cm) base cabinet. | 24" (61 cm) base cabinet. |
CABINET OPENING DIMENSIONS
The cooktop sides of the
If you have a square finish (flat) countertop and the opening width is 30" (76.2 cm), no countertop preparation is required.
Formed
Tile countertops may need trim cut back 3/8" (1.0 cm) from each front corner and/or rounded edge flattened.
If countertop opening width is greater than 30" (76.2 cm), adjust the 3/8" (1.0 cm) dimension.
Countertop must be level. Place level on countertop, first side to side; then front to back. If countertop is not level, range will not be level. Range must be level for satisfactory baking performance.
Freestanding Range
13" (33 cm) |
| |
upper cabinet | For minimum | |
depth | clearance to the | |
30" (76.2 cm) min. | top of the cooktop, | |
see NOTE*. | ||
opening width | ||
|
18" (45.7 cm) upper cabinet to countertop
30"
(76.2 cm) min. opening width
4" (10.2 cm) min. clearance from both sides of range to side wall or other combustible material
Cabinet door |
or hinge |
Cabinet opening dimensions shown are for 25” (64 cm) countertop depth, 24” (61 cm) base cabinet depth and 36” (91.4 cm) countertop height.
Slide-in Range
13" (33 cm)
|
|
| upper cabinet |
|
| For minimum | |
|
|
| depth |
|
| clearance to the | |
|
|
|
|
| top of the cooktop, | ||
|
|
|
|
|
|
| |
|
|
| 30" | (76.2 cm) min. |
|
| see NOTE*. |
|
|
| opening width |
| 22 3/4" (57.8 cm) | ||
18" (45.7 cm) upper |
|
|
|
| |||
cabinet to countertop |
|
|
|
| opening depth | ||
1/4"
(6.2 cm) radius both corners
30"
(76.2 cm)³⁄₈"
(1.0 cm)
30 ³⁄₄"
Junction box - 8" | should not | |
(20.3 cm) to 22" (55.9 cm) | ||
extend into | ||
from either cabinet, 7" | ||
the cutout. | ||
(17.8 cm) max. from floor | ||
|
4" (10.2 cm) min. clearance from both sides of range to side wall or other combustible material
30"
(76.2 cm) min. opening width
(78.1 cm)
NOTE: 24" (61 cm) min. when bottom of wood or metal cabinet is protected by not less than 1/4" (0.64 cm) flame retardant millboard covered with not less than No. 28 MSG sheet steel, 0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) aluminum or 0.020" (0.5 mm) copper.
30" (76.2 cm) min. clearance between the top of the cooking platform and the bottom of an unprotected wood or metal cabinet.
If installing a range hood or microwave hood combination above the range, follow the range hood or microwave hood combination installation instructions for dimensional clearances above the cooktop surface.
| Cabinet door | |
Junction box - 8" | or hinge | |
should not | ||
(20.3 cm) to 22" (55.9 cm) | ||
extend into | ||
from either cabinet, 7" | ||
the cutout. | ||
(17.8 cm) max. from floor | ||
|
Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation | Ref. 9763461 |
Instructions packed with product. Specifications subject to change without notice. |