KitchenAid KHMS2050S dimensions Product Model Numbers, Cabinet Opening Dimensions

Page 1

®

Microwave Hood Combination

PRODUCT MODEL NUMBERS

KHMS2050S

CABINET OPENING DIMENSIONS

AB

Electrical: A 120-volt, 60-Hz, AC-only, 15- or 20-amp electrical supply located in the upper cabinet as close as possible to the microwave oven hood. A time-delay fuse or circuit breaker and separate circuit is recommended.

OVERALL DIMENSIONS

18¹⁄₄"

(46.4 cm)

29

⁷⁄₈" (75.9 cm)

 

30"

 

(76.2 cm)

33"

min.

 

(83.2 cm)

 

typical*

12" (30.5 cm) min.

 

 

13" (33.0 cm) max.

69" (175.3 cm) min.

 

NOTE: The grounded 3 prong outlet must be inside the upper cabinet.

*33" (83.2 cm) is typical for 69" (175.3 cm) installation height. Exact dimension may vary depending on type of range/cooktop.

15¹⁄₂"

(39.4 cm)

18¹⁄₈"

(46.0 cm)

A. 2" x 4" wall stud

B. Grounded 3 prong outlet

VENTING REQUIREMENTS

Roof venting

roof cap

Wall venting

Recommended vent length

 

 

 

 

 

 

wall cap

Use 3-1/4" x 10" or 6" vent. The total length of the vent system

 

 

including straight vent, elbow, transitions, wall or roof caps

 

 

 

 

 

 

must not exceed the equivalent of 140 feet of

 

 

 

3-1/4" x 10" rectangular or 6" diameter round vent. For best

 

 

 

performance, use no more than three 90° elbows. To calculate

 

 

3-1/4" x 10"

the length of system you need, add the equivalent feet for

 

 

through-the-wall

each vent piece used in the system. See examples below.

 

3-1/4" x 10"

 

 

 

 

 

through-the-roof

 

3-1/4" x 10" vent system

Recommended standard fittings

For wall or roof venting methods:

 

 

 

 

 

If the wall exhaust method is chosen, be sure that

3-1/4" x 10"

 

 

 

 

 

 

 

90° elbow

6 ft.

wall cap

 

 

 

 

there is proper clearance within the wall so the vent

 

 

 

 

 

 

 

 

 

 

 

 

fits properly and the damper blade opens fully.

 

 

 

 

 

 

 

 

Wall and roof caps must have back-draft damper.

 

 

 

 

 

 

 

 

We recommend:

2 ft.

1 - 3-1/4" x 10"

 

 

 

 

 

 

using rigid metal vent.

 

 

3-1/4" x 10"

3-1/4" x 10"

3-1/4" x 10"

 

90° elbow

= 25 ft.

that length of vent and number of elbows should

 

 

 

 

to 6" = 5 ft.

roof cap = 24 ft.

90° elbow = 25 ft.

 

1 - wall cap

= 40 ft.

 

 

 

 

be kept to a minimum to provide efficient

 

8 feet straight

=

8 ft.

 

 

 

 

performance.

 

Length of

 

 

 

 

 

 

that size of vent should be uniform.

 

3-1/4" x 10" system

= 73 ft.

 

 

 

 

using duct tape to seal all joints in the vent

 

 

 

 

 

6" vent system

 

 

 

 

 

 

 

system.

 

 

 

 

 

 

 

 

 

 

 

90° elbow

3-1/4" x 10"

45° elbow

3-1/4" x 10"

using caulking compound to seal exterior wall or

90° elbows

6 ft.

 

wall cap

6" = 10 ft.

wall cap =

6" = 5 ft.

90° flat

roof opening around cap.

 

 

 

 

 

40 ft.

 

elbow= 10 ft.

two elbows should not be installed together.

 

 

 

 

 

 

 

 

 

 

 

 

If the existing vent is round, a rectangular- to-round adapter must be used and a rectangular 3" extension vent between the damper assembly and the adapter must be installed to prevent sticking of the exhaust damper.

We do NOT recommend:

 

 

 

 

 

 

1

- transition

=

5 ft.

 

 

 

 

 

 

 

 

 

2 ft.

flexible metal vent.

 

 

 

2

- 90° elbows

= 20 ft.

 

 

 

 

 

 

 

 

 

 

 

 

NOTE: If flexible metal vent must be used, calculate

 

 

 

 

 

 

1

- wall cap

= 40 ft.

 

 

 

 

 

 

 

 

 

 

 

 

8 feet straight

=

8 ft.

each foot of flexible metal vent as two feet of rigid

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Length of 6" system

= 73 ft.

metal vent. Flexible metal elbows count twice as

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

much as standard elbows.

 

 

 

 

 

 

 

 

 

 

transition

 

 

 

 

 

Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice.

Dimensions are for planning purposes only. For complete details, see Installation

Ref. 8206329

Instructions packed with product. Specifications subject to change without notice.

08-08-06

Image 1
Contents Overall Dimensions Cabinet Opening DimensionsProduct Model Numbers Venting Requirements

KHMS2050S specifications

The KitchenAid KHMS2050S is a sleek, stylish microwave that seamlessly combines functionality with modern design. This built-in microwave is specifically engineered for those who value kitchen innovation, efficiency, and aesthetics. With its stainless steel finish, it not only complements contemporary kitchen decor but is also easy to clean.

One of the primary features of the KitchenAid KHMS2050S is its substantial 2.0 cubic feet capacity, which allows for ample space to accommodate larger dishes and containers. This feature is especially beneficial for families or those who frequently cook with large quantities. The interior is equipped with a turntable, providing even heating and consistent cooking results, ensuring that meals come out perfectly every time.

The KHMS2050S employs advanced cooking technologies designed to enhance user convenience and cooking performance. Its sensor cooking feature automatically adjusts cooking times and power levels, depending on the specific dish being prepared. This ensures optimal results without the guesswork involved in manual timing. Additionally, the microwave's specialized settings for popcorn, baked potatoes, and other common items further simplify meal preparation.

For those who enjoy entertaining or cooking elaborate meals, the KitchenAid KHMS2050S offers a variety of cooking presets that enhance versatility. It includes options for defrosting, reheating, and cooking with one-touch controls, which save time and streamline the cooking process.

Safety is also considered in the design of the KHMS2050S. It features a child lock to prevent unintended use, making it a practical choice for households with children. Furthermore, the microwave is equipped with an easy-to-read LED display, allowing users to monitor cooking progress at a glance.

In addition to its performance and safety features, the KitchenAid KHMS2050S boasts a quiet operation, making it an essential appliance for any modern kitchen where noise levels are a concern.

In summary, the KitchenAid KHMS2050S is a powerful, reliable, and aesthetically pleasing microwave that offers a combination of advanced technology, user-friendly features, and safety. Whether you're reheating leftovers or preparing a multi-course meal, this microwave is designed to enhance your cooking experience. With its impressive capacity and efficient features, it is the ideal choice for anyone looking to elevate their kitchen functionality.