KitchenAid KUIA18NNJ, KUIA15NLH Removing the ICE Maker Door & Gasket, To remove the door gasket

Page 45

REMOVING THE ICE MAKER DOOR & GASKET

(15″ MODELS)

1.To remove the door, remove the top door screw from the ice maker door, and pull the door off the bottom hinge.

Top Door Screw

2.To remove the door gasket:

a)Open the ice maker door.

b)Pull the gasket out of the door track. NOTE: Be sure to check the new gas- ket for a proper seal after you install it.

Door Track

Door Gasket

4-21

Page 44 Page 46
Image 45
Page 44 Page 46
Contents 18″ Automatic ICE Makers Goals and Objectives ForwardTable of Contents Wiring Diagram & Strip Circuits Safety First Electrical Power Supply & Grounding RequirementsGeneral Electrostatic Discharge ESD Sensitive Electronics Serial Number Model NumberYear of Introduction Model & Serial Number Location Model & Serial Number Label LocationSpecifications Kitchenaid ICE Maker Warranty Page Installation Information Electrical Supply RequirementsRecommended Grounding Method Water Supply and Drain Connections Connecting the Water LineGravity Drain System Connecting the DrainDrain Pump System On Some Models Theory of Operation Operating SystemsRefrigeration System Water System Electrical System ICE Making Cycle Operational CyclesElectrical System Refrigeration SystemHarvest Cycle Diagnostics / Clean CycleNEW ICE Maker Control Board #6100499 Models with Internal Drain Pumps Page Component Locations Component AccessTo remove the cutter grid To remove the bin thermistorOn the next To remove the evaporator thermistorTo remove the water distributor To remove the electronic control board Removing the Electronic Control Housing ComponentsTo remove the cutter grid transformer Removing the Water Recirculation Pump Removing the Condenser FAN Motor Disconnect Tubing Internal Drain Pump Nut Marking On Fan Removing the Evaporator Screw Water Trough Remove the Permagum from the liner channel Reassembly Notes Removing the Water Inlet Valve To remove the hot gas valve Removing the HOT GAS Valve & SolenoidRemoving the Condenser Removing the Compressor Pull the two clips off the rear studs of the compressor Removing the Internal Drain Pump Only on Some Models To remove the door gasket Removing the ICE Maker Door & Gasket18″ Models Bottom Door Cap Screws Door Hinge Hinge Pin Channel Support Reassembly Notes Page BIN Thermistor Component TestingCutter Grid Transformer Cutter GridCondenser FAN Motor Water Recirculation PumpHOT GAS Valve Solenoid Water Inlet Valve SolenoidTo test the compressor windings COMPRESSOR, Overload PROTECTOR, & RelayTo test the relay Pushbutton Switch Assembly Page Water and ITS Effect on Making ICE Diagnosis & TroubleshootingEffect on ICE Quality Effect on ICE MakerProblem Probable Cause Test Procedure-Action Troubleshooting ChartWill not make ice Defective bin thermistor Overview Diagnostic Flow Chart for ICE Maker Control Board #6100499Flush Mode 5 minutes Idle Mode Page Unit leaves Freeze Mode Warmer Ambients Page Reservoir must be drained prior to restarting the unit Page Wiring Diagram Wiring Diagram & Strip CircuitsICE Making Mode Harvest ModeStrip Circuits Last 47 Minutes of DIAGNOSTICS/CLEAN Mode First 25 Seconds of DIAGNOSTICS/CLEAN ModePage Cleaning the ICE Maker Cleaning Evaporator PlateTech Tips Cleaning Solution On Pad Thick Thin Adjusting the ICE ThicknessPage Product Specifications Warranty Information Sources
Related manuals
Manual 1 pages 6.61 Kb

KUIS185J, KUIA15NRH, KUIS18NNJ, KUIA18PNL, KUIA15NLH specifications

KitchenAid has long been synonymous with quality in the realm of kitchen appliances, and its line of undercounter ice makers, specifically the models KUIA18NNJ, KUIV18NNM, KUIS18PNJ, KUIA18PNL, and KUIS18NNJ, exemplifies the brand's commitment to innovation and functionality. These ice makers are designed to deliver a reliable supply of ice without taking up valuable space in your kitchen.

The KUIA18NNJ and KUIV18NNM models both showcase a sleek stainless steel exterior which not only adds a modern aesthetic to any kitchen but also ensures durability. These models come equipped with advanced insulation technology that helps keep the ice frozen for extended periods, even during power outages. One key feature is their ability to produce clear, restaurant-quality ice, making them perfect for entertaining guests or simply enjoying a cold beverage at home.

The KUIS18PNJ and KUIA18PNL models, available in panel-ready finishes, allow homeowners to customize the look of the appliances to match their cabinetry. This versatility in design ensures that these ice makers seamlessly blend into any kitchen decor, offering both functionality and style. Each unit has a robust production capacity, capable of producing up to 50 pounds of ice per day, which ensures that you will never run out during those summertime gatherings.

In terms of technology, these ice makers are equipped with easy-to-use digital controls that allow users to monitor ice production and adjust settings with minimal effort. Additionally, the efficient cooling system not only conserves energy but also helps to maintain lower operating costs.

Moreover, the KUIS18NNJ model features a built-in water filtration system that enhances the quality of the ice produced by filtering out impurities, ensuring that every cube is clear and refreshing.

With quiet operation and low vibrations, these ice makers are perfect for any living environment, making them a great addition to any home. Whether hosting parties or simply enjoying a quiet evening, KitchenAid's undercounter ice makers offer a perfect blend of practicality, style, and advanced technology to meet the modern consumer's needs.
Top Page Image Contents