Before you start, Parts supplied | Whirlpool RH3736 specification

Before you start...

Your safety and the safety of

others is very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill

or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING”. These words mean:

DANGER

You can be killed or seriously injured if you don’t immediately follow instructions.

WARNING

You can be killed or seriously injured if you don’t follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

Important: Observe all governing codes and ordinances.

Proper installation is your responsibility. Make sure you have everything necessary for correct installation. It is the responsibility of the installer to comply with the clearances specified.

Check the location where the range hood will be installed. The location should be away from strong draft areas, such as windows, doors, and strong heating vents.

Mobile home installation

The installation of this range hood must conform to the Manufactured Home Construction Safety Standards, Title 24 CFR, Part 328 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD, Part 280) or when such standard is not applicable, the Standard for Manufactured Home Installation

1982 (Manufactured Home Sites, Communities and Setups) ANSI A225.1/NFPA 501A*, or latest edition, or with local codes.

WARNING — TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable Codes and Standards, including Fire Rated Construction. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent back drafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society of Heating Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Ducted fans must always be vented to the outdoors.

WARNING — To reduce the risk of fire, use only metal ductwork.

This unit must be grounded.

This hood is factory set for vented installations. For non-vented installations, purchase Filter Kit No. 883093 (includes Filter/Light Lens No. 883149 and Charcoal Filter Pads No. 883151) from your dealer.

Tools and materials needed for installation:

• flat blade	• 1-1/4" (3.0 cm)
screwdriver	drill bit
• pliers	• 1/8" (or 3 mm) drill
• drill	bit for pilot holes
• ruler	• pencil

For vented installations, you also need:

• compass or 8"	• duct tape
(20.3 cm) circle	• 7" (17.8 cm) round
template	damper if using
• metal snips	7" (17.8 cm) round
• keyhole saw	vent system
• saber saw

Cabinets with recessed bottoms:

•2, 2" (5.8 cm) wide filler strips. Length and thickness determined by recess dimensions.

•4 flat head wood screws or machine screws with washers and nuts to attach filler strips.

Parts supplied:

•filter with built-in light lens

•3-1/4" x 10" (8.3 x 25.4 cm) damper/vent connector

•parts bag

Electrical requirements

Important: Observe all governing codes and ordinances.

It is the customer’s responsibility:

•To contact a qualified electrical installer.

•To assure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70

— latest edition*, or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No.0-M91 - latest edition** and all local codes and ordinances.

A separate ground wire must be used. It is recommended that a qualified electrician determine that the ground path is adequate.

A 120-volt, 60-Hz, AC-only, fused electrical system is required. A separate 15-amp circuit is recommended.

Do not ground to a gas pipe.

Check with a qualified electrician if you are not sure range hood is properly grounded.

Do not have a fuse in the neutral or ground circuit.

IMPORTANT:

Save Installation Instructions for electrical inspector’s use.

The range hood must be connected with copper wire only.

The range hood should be connected directly to the fused disconnect (or circuit breaker) box through flexible armored or nonmetallic sheathed copper cable. A U.L.- or C.S.A.-listed strain relief must be provided at each end of the power supply cable. Wire sizes (COPPER WIRE ONLY) and connections must conform with the rating of the appliance as specified on the model/serial rating plate.

Wire sizes must conform to the requirements of the National

RH3736 specifications

The Whirlpool RH3736 is a standout appliance in the realm of refrigerators, showcasing a blend of modern technology and stylish design. With its sleek exterior and thoughtful engineering, it serves as an essential addition to any kitchen.

One of the main features of the Whirlpool RH3736 is its generous storage capacity. With multiple shelves and spacious door bins, it provides ample room for groceries, beverages, and leftovers. The adjustable shelves allow users to customize the layout to accommodate various sizes of items, making organization a breeze.

This model is equipped with advanced cooling technology, ensuring optimal preservation of food for longer durations. The Adaptive Defrost feature is designed to help save energy by sensing when the refrigerator needs to defrost, thereby minimizing energy consumption. Coupled with the Fresh Flow air filter, it helps to eliminate odors and maintains an inviting atmosphere inside.

Another notable characteristic of the Whirlpool RH3736 is its Energy Star certification. This means the unit meets rigorous efficiency standards, allowing homeowners to enjoy lower utility bills while contributing to environmental sustainability. The Eco-friendly design is a crucial aspect for those looking to reduce their carbon footprint without sacrificing performance.

The refrigerator also boasts a unique temperature management system. This technology senses and adapts to changes in temperature with remarkable precision. Through multiple sensors, it monitors the temperature and humidity inside the fridge, promoting optimal conditions for food storage. This innovation helps to keep produce fresh and minimizes spoilage.

In terms of convenience, the Whirlpool RH3736 comes with LED lighting that illuminates the interior for easy visibility. The bright, energy-efficient lights are designed to last longer than traditional bulbs, making them a practical choice for everyday use.

Additionally, the refrigerator features a sleek and modern finish that can seamlessly integrate into various kitchen designs. Whether you prefer stainless steel or a classic white finish, the Whirlpool RH3736 offers a stylish appearance that enhances any kitchen aesthetic.

Overall, the Whirlpool RH3736 stands out as a top choice for those seeking a reliable, energy-efficient refrigerator packed with innovative features and an impressive design. With its commitment to food preservation and user-friendly technology, this model is set to meet the demands of modern households.