Whirlpool RH8930XLS manual C5mf, Fig&E

Page 2

1.Make a template or transfer measurements shown in Fig. 3 to cabinets or wall.

2.Cut holes to accomodate ventilating duct allowing W’ (.6 cm) clearance on all four sides for back vent. Allow J/4”(1.9 cm) clearance toward front for vertical vent. Allow %” (.6 cm) on other three sides for top vent.

3.Cut appropriate hole for electrical wiring.

4.Run wire through wall or cabinets according to National Electrical Code and Applicable local codes. (DO NOT turn power on until installation is complete.)

5.Remove blower housing and filters for easier installation. See exhaust unit assembly illustration on page 6.

6.Remove screw holding junction box cover.

7.Remove proper electrical knockout. See Figure 3.

8.Remove proper venting knockout. See Figure3. NOTE: If horizontal discharge is selected an additional knockout in the blower cradle must be removed.

9.Attach the damper as shown in Figure 5 for vertical discharge or Fig. 6 for horizontal discharge.

10.Lift the hood into position. Mark location of four mounting holes.

11.Remove hood and start all four screws in center of narrow neck of keyhole slot marked on cabinet bottom.

12.Lift the hood into position simultaneously feeding the electrical wire through the knockout. Follow applicable local codes and/or latest National Electrical Code for electrical connector to be used at field wiring entrance.

13.Tighten screws to secure hood. Be sure screw head is in narrow neck of keyhole slot.

14.Install proper duct work. See page 4

15.Complete electrical wiring in junction box according to the National Electrical Code and applicable Local Codes NOTE: This unit must be permanently grounded in accordance with the National Electrical Code and applicable Local codes.

16.Replace junction box cover.

17.Replace blower. Note different blower positions in Figure 5 for vertical venting and Figure 6 for horizontal venting. See Page 3 for correct blower installation.

18.Replace blower cover, light frame assembly and filters.

NOTE: It has been found that a large part of the energy loss of the average home is due to outside air infiltrating the structure. Seal around ductwork where it passes through outside walls or ceiling. Seal around electrical wiring also.

19.Be sure that damper which is supplied with this model is properly installed. (See Figures 1 8 2).

6-1

c5mf

FIG&E 5

FIGURE 6

 

Page 2

TRAIN CAP

IF RAIN CAP HAS

A CAMPER, REMOVE

DAMPEF) BLADE

FROM rCOO0

FIGURE 1

VERTICAL VENTING ,a

3%. x IO” RECTANGULAR

IF RAIN CAP HAS

A DAMPER. REMOVE

DAMPER BLAOE

FROM HOOD.

FIGURE 2

HORIZONTAL VENTING

FIGURE 4

Page 1 Page 3
Image 2
Page 1 Page 3
Contents Kitchen Range Hood Model RH8930XLS Motor Lights FilterC5mf FIG&EVertical Discharge Horizontal DischargeVertical Venting LengthIncrease Speed TurnDecrease Speed UP ArrowBlower Cover Assy Cover MTG Cover Retaining ScrewsFive PIN Connector C Board Removal

RH8930XLS specifications

The Whirlpool RH8930XLS is a sophisticated and versatile tumble dryer, designed to provide optimal performance while catering to the needs of modern households. Known for its efficient drying capability, this model combines advanced technology with user-friendly features to ensure laundry is dried quickly and effectively.

One of the standout features of the RH8930XLS is its Heat Pump Technology. This innovative system not only reduces energy consumption but also allows the dryer to recycle hot air for maximum efficiency. This not only lowers utility bills but also ensures gentler drying that helps preserve the quality of fabrics over time. The Energy Efficiency rating is top-notch, making it an eco-friendly choice for conscious consumers.

The appliance is equipped with a substantial drum capacity, allowing users to dry large loads in one go. This capacity is particularly beneficial for families or households with frequent laundry needs, minimizing the number of cycles needed and thus saving time. The unique drum design also promotes better circulation of air, which results in more consistent drying throughout.

In terms of settings, the RH8930XLS offers multiple drying programs suited for various fabric types and load sizes. Users can select from options such as Delicates, Wool, and Cotton programs, each tailored to handle laundry with care. The inclusion of a sensor drying feature further enhances the dryer’s functionality by automatically detecting moisture levels in the clothes and adjusting drying times accordingly. This ensures garments are dried to perfection without the risk of over-drying.

Another notable characteristic of the Whirlpool RH8930XLS is its user-friendly interface. The intuitive control panel features a clear display and straightforward buttons that allow for easy program selection and monitoring. Additionally, the drying cycle can be customized with a delay-start option, providing the flexibility to fit laundry chores into a busy schedule.

Maintenance is made simple with the RH8930XLS as well. The dryer is designed with an easy-access filter, allowing users to clean it with minimal effort. This ensures optimal performance and longevity of the appliance.

Overall, the Whirlpool RH8930XLS combines cutting-edge technology, energy efficiency, and practicality, making it an excellent addition to any home seeking a reliable and effective tumble dryer.
Top Page Image Contents