Whirlpool LI31HC/W10526058F Installation Requirements, Tools and Parts, Location Requirements

Page 4

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

Tools needed

Level

Drill with 1¼" (3.0 cm), ³⁄₈" (9.5 mm), ⁷⁄₆₄" (2.75 mm) and ¹⁄₈" (3.0 mm) drill bits

Pilot hole drill bits (determined by chimney support attachment method)

Pencil

Wire stripper or utility knife

Tape measure or ruler

Pliers

Caulking gun and weatherproof caulking compound

Vent clamps

Jigsaw or keyhole saw

Flat-blade screwdriver

Metal snips

Phillips screwdriver

Parts needed

Home power supply cable

½" (12.7 mm) UL listed or CSA approved strain relief

3 UL listed wire connectors

For vented installations, you will also need:

1 wall or roof cap

Metal vent system

For non-vented (recirculating) installations, you will also need:

Recirculating Kit Part Number W10294734 for non-vented (recirculating) installations only. See “Assistance or Service” section to order.

6" (15.2 cm) round metal vent duct. Length required is determined by ceiling height.

Parts supplied

Remove parts from packages. Check that all parts are included.

Hood ventilator assembly with canopy glass, retainer brackets, rubber seals, and light bulb installed.

Metal grease filter

60 - 4.2 x 8 mm screws

4 - 3.5 x 6.5 mm screws

4 - 5 x 45 mm screws

2 - 2.9 x 3 mm screws

T10 Torx®† adapter

T20®† Torx® adapter

2 - Upper vent covers

2 - Lower vent covers

4 - Plastic vent clips

Mounting template

Upper horizontal support bracket

Horizontal support

8 - Vertical supports

Vent transition with back draft damper installed.

2 - 3.5 x 9.5 mm mounting screws

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

Have a qualified technician install the range hood. It is the installer's responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located behind the left filter on the rear wall of the vent hood.

Canopy hood location should be away from strong draft areas, such as windows, doors and strong heating vents.

Cabinet opening dimensions that are shown must be used. Given dimensions provide minimum clearance.

Grounded electrical outlet is required. See “Electrical Requirements” section.

Because of the size and weight of this island hood, the chimney support must be securely attached to the ceiling.

For plaster or drywall ceilings, the chimney support must be attached to joists. If this is not possible, you must build a support structure behind the plaster or drywall. The support structure must be able to support 80 lbs (36.6 kg).

This range hood is recommended for use with cooktops with a maximum total rating of 60,000 BTUs or less.

The range hood is factory set for venting through the roof or wall.

For non-vented (recirculating) Installation see “Non-vented (recirculating) Installation” in “Install Range Hood” section. Recirculating Kit Part Number W10294734 is available from your dealer or an authorized parts distributor.

All openings in ceiling and wall where range hood will be installed must be sealed.

For Mobile Home Installations

The installation of this range hood must conform to the Manufactured Home Construction Safety Standards, Title 24 CFR, Part 328 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD, Part 280) or when such standard is not applicable, the standard for Manufactured Home Installation 1982 (Manufactured Home Sites, Communities and Setups) ANSI A225.1/NFPA 501A, or latest edition, or with local codes.

†®TORX and T20 are registered trademarks of Acument Intellectual Properties, Inc.

4

Image 4
Contents 36 91.4 CM ISLAND-MOUNT Canopy Range Hood Range Hood Safety Table of ContentsImportant Safety Instructions Tools and Parts Installation RequirementsLocation Requirements Product Dimensions Installation DimensionsCold Weather Installations Venting RequirementsFor Non-Vented recirculating Installations Electrical RequirementsVenting Methods Example Vent SystemPrepare Location Installation InstructionsComplete Preparation Install Range Hood Non-Vented recirculating InstallationRange Hood Installation Assemble Range HoodMake Electrical Connection Install Duct Covers Complete Installation Range Hood USE Range Hood ControlsOperating the light Operating the blowerCleaning Range Hood CareWiring Diagram SE123CAssistance or Service AccessoriesU.S.A CanadaWhirlpool Major Appliance Limited Warranty Sécurité DE LA Hotte DE Cuisinière Votre sécurité et celle des autres est très importanteImportantes Instructions DE Sécurité Exigences d’emplacement Exigences DinstallationOutils et pièces Dimensions d’installation Dimensions du produitExigences concernant lévacuation Spécifications électriques Instructions D’INSTALLATION Préparation de lemplacementInstallation des vis de montage de la hotte Achever la préparationInstallation de la hotte Installation sans décharge à l’extérieur recyclageInstallation de la hotte Assemblage de la hotteRaccordement électrique Raccordement du circuit d’évacuationInstallation des cache-conduits Vis de 2,9 x 3 mmAchever linstallation Commandes de la hotte de cuisinière Utilisation DE LA HottePour faire fonctionner la lampe Utilisation du ventilateurEntretien DE LA Hotte NettoyageSchéma DE Câblage Ph1 Neu TerreAccessoires Assistance OU ServiceAu Canada Garantie Limitée DES W10526058F

LI31HC/W10526058F specifications

The Whirlpool LI31HC/W10526058F is a state-of-the-art refrigerator that exemplifies modern design and advanced technology, making it an ideal addition to any contemporary kitchen. This model is recognized for its stylish aesthetics, energy efficiency, and innovative features that cater to the needs of every household.

One of the standout characteristics of the LI31HC is its spacious interior, designed to maximize storage while maintaining an organized layout. With adjustable shelves and humidity-controlled crispers, users can customize the configuration to accommodate various food items, from large platters to delicate produce. The refrigerator boasts a generous capacity, ensuring ample space for groceries and leftovers.

Energy efficiency is a pivotal aspect of the Whirlpool LI31HC/W10526058F. With an impressive Energy Star certification, this refrigerator not only helps to reduce utility bills but also minimizes environmental impact. The appliance features advanced insulation and efficient cooling systems that work together to maintain optimal temperatures, ensuring food stays fresh for longer periods.

Whirlpool’s commitment to innovation is evident in the incorporation of adaptive cooling technology. This feature allows the refrigerator to monitor internal conditions and adjust cooling settings accordingly, maintaining the freshest environment for food storage. The frost-free design is another key benefit, eliminating the need for manual defrosting and providing hassle-free maintenance.

Another notable technology integrated into the LI31HC is the advanced filtration system. This ensures that both water and ice are purified for safe consumption, providing peace of mind for families who prioritize health and wellness. The sleek ice maker is conveniently located, ensuring easy access without compromising the refrigerator's design.

In terms of usability, the LI31HC/W10526058F includes intuitive controls, making it simple to customize settings to suit individual preferences. The LED lighting inside provides brilliant visibility, allowing users to easily find items even in low-light conditions.

Overall, the Whirlpool LI31HC/W10526058F combines functionality with modern aesthetics, making it a remarkable choice for those seeking a reliable and stylish refrigerator. Its advanced features cater to the needs of today's consumers, making food storage a seamless experience. Whether you're preparing a family meal or hosting friends, this refrigerator is equipped to handle it all with grace and efficiency.