Installation Instructions, PrepareLocation

INSTALLATION INSTRUCTIONS

PrepareLocation

■It is recommended that the vent system be installed before hood is installed.

■Before making cutouts, make sure there is proper clearance within the ceiling or wall for exhaust vent.

■Check your ceiling height and the hood height maximum before you select your hood.

1.Disconnect power.

2.Determine which venting method to use: roof, wall, or non- vented.

3.Select a flat surface for assembling the range hood. Place covering over that surface.

WARNING

Excessive Weight Hazard

Use two or more people to move and install range hood.

Failure to do so can result in back or other injury.

4.Using 2 or more people, lift range hood onto covered surface.

Range Hood Mounting Screws Installation

5.Determine and mark the centerline on the wall where the canopy hood will be installed.

6.Select a mounting height between a minimum of

24" (61.0 cm) for an electric cooking surface, a minimum

of 27" (68.6 cm) for a gas cooking surface, and a suggested maximum of 36" (91.4 cm) above the range to the bottom of the hood. Mark a reference line on the wall.

7.Tape template in place, aligning the template centerline and bottom of template with hood bottom line and with the centerline marked on the wall.

DRILL2 (TW O)3/16"PILOTHOLESTHROUGH STUDSOR REAR W ALLSUPPORT

Vertical
Centerline	REAR W ALL

M OUNTING TEM PLATE

ALIGN BOTTOM EDGE

W ITH PENCILLINE

INDICATING BOTTOM

OFTHEHOOD

Installation Height

HorizontalLine

A.Centerline

B.Fastener locations

C.Mounting height reference

8.Mark centers of the fastener locations through the template to the wall.

IMPORTANT: All screws must be installed into wood. If there is no wood to screw into, additional wall framing supports may be required.

Remove the template.

9.Drill ³⁄₁₆" (4.8 mm) pilot holes at all locations where screws are being installed into wood.

10.Install the 2 - 5 x 45 mm mounting screws. Leave a

¹⁄₄" (6.4 mm) gap between the wall and the back of the screw head to slide range hood into place.

¹⁄₄" (6.4 mm)

Vent Cover Support Bracket Installation

Installations using telescoping upper and lower vent cover assembly

1.Position vent cover bracket on wall about ¹⁄₈" (3.0 mm) away from the ceiling.

2.Mark the hole locations.

3.Drill ³⁄₈" (9.5 mm) holes for wall anchors and insert anchors flush with the wall.

A. 8 x 40 mm drywall anchors

B. Centerline on wall

C. Vent cover support bracket

D. 5 x 45 mm screws

4.Attach vent cover support bracket to wall.

Complete Preparation

1.Determine and make all necessary cuts in the wall for the vent system. Install the vent system before installing the hood. See “Venting Requirements” section.

2.Determine the required height for the home power supply cable and drill a 1¼" (3.2 cm) hole at this location.

3.Run the home power supply cable according to the National Electrical Code or CSA Standards and local codes and ordinances. There must be enough ½" conduit and wires from the fused disconnect (or circuit breaker) box to make the connection in the hood’s electrical terminal box.

NOTE: Do not reconnect power until installation is complete.

4.Use caulk to seal all openings.

LI3Y3B, W10320580B specifications

The Whirlpool LI3Y3B, model number W10320580B, is a notable addition to the brand’s range of refrigeration appliances, designed to meet the demands of modern households. This refrigerator boasts a blend of advanced technologies and user-friendly features, making it both efficient and convenient for everyday use.

One of the primary features of the LI3Y3B is its generous storage capacity, allowing users to store a significant amount of food and beverages without compromising on accessibility. The interior space is designed with adjustable shelves that can be configured to accommodate items of varying sizes, optimizing storage efficiency. This adaptability enhances user convenience and ensures that there is ample room for all essentials.

Whirlpool has incorporated a range of advanced cooling technologies into the LI3Y3B. The refrigerator is equipped with a multi-air flow system that evenly distributes cool air throughout the appliance, ensuring that every corner remains at the optimal temperature. This technology not only helps to preserve the freshness of food items, but also reduces the chances of spoilage, extending the lifespan of perishable goods.

The presence of an energy-efficient compressor in the LI3Y3B is another standout characteristic. This feature minimises energy consumption while maintaining consistent cooling performance. Households looking to reduce their energy bills will appreciate the refrigerator’s ability to operate efficiently without sacrificing cooling capabilities.

Additionally, the LI3Y3B comes with a user-friendly digital control panel that enables users to effortlessly adjust temperature settings and monitor the appliance’s performance. This feature empowers users to maintain their food at the ideal temperature, enhancing food preservation efforts.

The exterior design of the LI3Y3B is equally compelling, featuring a sleek and modern look that seamlessly blends with various kitchen styles. The durable finish is not only aesthetically pleasing but also resistant to fingerprints and smudges, ensuring that the refrigerator remains clean and attractive over time.

Overall, the Whirlpool LI3Y3B, W10320580B stands out in the refrigerator market with its combination of ample storage, advanced cooling technologies, energy efficiency, and modern design. Designed for practicality and convenience, it is an excellent option for families and individuals alike who seek reliability in their kitchen appliances. Choosing this refrigerator means investing in both quality and performance, ensuring that food stays fresh and easily accessible for all culinary needs.