Hotpoint BS73 BS63 manual Installation of Built-in Ovens

Page 14

Installation

The appliance must be installed only by a qualified per- son in compliance with the instructions provided. The manufacturer declines all responsibility for improper installa- tion which may harm persons and animals and damage property.

Important: The power supply to the appliance must be cut off before any adjustments or maintenance work is done on it.

Installation of Built-in Ovens

In order to ensure that the built-in appliance functions prop- erly, the cabinet containing it must be appropriate. The figure below gives the dimensions of the cut-out for installation un- der the counter or in a wall cabinet unit.

 

 

 

mm.23

 

 

 

.

mm.

 

 

 

 

 

45

mm

 

mm.595

 

 

 

mm.567

 

558

mm.

593

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5 mm.

 

 

 

 

 

 

595

mm.

 

.

 

 

 

 

 

 

545

mm

 

 

 

 

 

 

 

 

 

 

 

 

 

.

 

 

 

 

 

 

 

 

mm

 

 

 

 

 

 

 

24

 

 

 

 

 

 

N.B.: Installation in compliance with the consumption declaration

 

.

45

mm

.

 

min

mm.595

 

 

23 mm.

.mm567

 

 

585-575mm.

595mm.

 

.

 

 

 

 

 

558

 

 

 

45

mm

 

 

 

 

 

mm.

 

 

.

 

 

 

 

 

 

 

 

 

min

 

 

 

5 mm.

 

 

 

 

 

 

 

 

595

mm.

 

.

 

 

 

 

 

 

 

 

545

mm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

.

 

 

 

 

 

 

 

 

 

 

mm

 

 

 

 

 

 

 

 

 

24

 

 

 

 

 

 

 

 

In order to ensure adequate ventilation, the back panel of the cabinet unit must be removed. Installing the oven so that it rests on two strips of wood is preferable. If the oven rests on a continuous, flat surface, there must be an aperture of at least 45 x 560 mm.

.

45

mm.

mm

 

560

 

 

 

 

1 4

The panels of the adjacent cabinets must be made of heat- resistant material. In particular, cabinets with a veneer exte- rior must be assembled with glues which can withstand temperatures of up to 100 °C.

In compliance with current safety standards, contact with the electrical parts of the oven must not be possible once it has been installed.

All parts which ensure the safe operation of the appliance must be removable only with the aid of a tool.

For the correct centring of your appliance, position the 4 tabs on the sides of the oven in correspondence with the 4 holes on the perimeter of the frame. In particular, if the cabinet side panel:

is 20 mm thick: the removable part of the tab must be removed (Fig. A);

is 18 mm thick: use the first groove, which is factory-set (Fig. B);

is 16 mm thick: use the second groove (Fig.C)

Fig. A

Fig. B

 

 

 

 

Fig. C

To fasten the oven to the cabinet, open the door of the oven and attach it by inserting the 4 wood screws into the 4 holes located on the perimeter of the frame.

Image 14
Contents Instructions for Installation and Use Electric Multifunction Oven Model BS63 Model BS73Page Contents Introduction For Your Safety AlwaysControl Panel Function selector Temperature control Know your OvenOven light Setting the digital clockControls Cooking without the ProgrammerMulti-cooking Mode Fan ModeFast cooking Mode Pizza ModeHow to set a programme to automatically switch off and on Minute Minder FeatureBuzzer volume To cancel a cooking schedule already programmedUsing the Grill Cooking AdviceUsing the Fast Cooking Mode Cooking on More Than One ShelfPastry is too dark on top Baking CakesPastry is too dry OutsideCooking Chart FanCare and Cleaning Installation Installation of Built-in OvensElectrical Connection N LPage Page Genuine Parts and AccessoriesUK 08709 077 After Sales ServiceRepair Service and Information Help Desk Extended WarrantiesGuarantee terms and conditions GuaranteeSatisfaction guaranteed or your money back Recycling & Disposal InformationKey Contacts Repair Service and Information DeskGenuine Parts and Accessories