Hotpoint UQ89I manual General, Final Installation

Page 24

Installation

Electrical Requirements

GB For your own safety, we recommend that your cooker is installed by a competent person such as one who is registered with NICEIC (National Inspection Council for Electrical Installation Contracting). The cooker should be installed in accordance with the latest edition of the IEE Regulations.

Warning: This appliance must be earthed.

Electrical Connections

The installer must check that the voltage shown on the rating plate corresponds with the house electricity supply. The cooker must be supplied via a suitable double pole isolating switch, having a contact separation of at least 3mm in all poles placed in a readily accessible position adjacent to the cooker. If the cooker is to be wired into a connector unit, this may be positioned behind the cooker providing the following requirements are met:

i)The connector unit must not project from the wall more than 25mm.

ii)The top of the connector must not be more than

130mm above floor level.

Remove the terminal cover at the rear base of the cooker. Pass the cable through the cable clamp and connect to the appropriate terminals provided. Allow sufficient cable for any future servicing. Tighten the screws on the cable clamp and replace the cover. Make main connections in the connector unit or cooker control unit. This appliance conforms to B.S. EN 55014 regarding suppression of Radio and Television reception interference.

A double Pole control switch having a minimum rating of 32 amps should be used to feed the cooker using a suitably rated cable. Where a hob is fitted adjacent to or over the cooker, a 45 amp Double Pole control switch should be used to feed both units via separate suitably rated cables.

We recommend a minimum of 4mm2 PVC insulated twin and earth cable conforming to B.S. 6004 for connection of each appliance.

In all cases adhere to routing details (see fig. 5).

This appliance must not be installed over any other appliance that generates heat such as a plinth heater.

Note: Due to many different types of installation, a mains cable is not supplied with this product. The installer will fit the correct type and length of cable.

GENERAL

The appliance is designed to be mounted on a floor between two adjacent cabinets.

The cabinets must be securely fixed to the wall and the cooker securely fixed to the cabinets.

This cooker must not be used free standing. Note; This cooker must not be fitted on a platform.

FINAL INSTALLATION

a.Ensure that the adjacent cabinets and the gap between them have dimensions in accordance with the diagram.

b.Assemble the plastic plugs provided into the fixing brackets. See diagram.

c.Fix the fixing brackets to the sides of the adjacent cabinets so that the centre line of the brackets are 570mm above the top of the plinth line and the front face of the plastic plug is level with the front face of the cabinet sides. See diagram.

d.Adjust the feet on the cooker to their minimum position, i.e. fully screwed in.

e.Slide the cooker centrally into the space between the cabinets ensuring the following:

i)The gap between the cabinet sides and the cooker is even along the length of the cabinet sides.

ii)The cable is routed away from any vents in the rear panel and is not trapped between the cooker and the wall, adjacent cabinets or under the feet

f.Adjust the feet using an open ended spanner until the bottom of the cooker door is in line with the top of the plinth. Using a spirit level, check that the cooker is level in all directions.

g.Check that the plinth can be fitted. If necessary re - adjust the feet and check that the cooker is level. Then lock the feet into position by tightening the lock nut using an open ended spanner.

h.Open the top oven door and fix the cooker to the brackets through the holes in the side trims.

i.Fix the plinth in position.

j.Ensure that there is a minimum gap of 1mm between the cooker side trim and the adjacent cabinet doors or drawer fronts.

k.If a hob is to be installed directly above the cooker it must not project downwards more than 20mm below the underside of the work top. Any projection of more than 10mm must not project more than 500mm from the wall.

Fig. 5

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Instructions for Installation and Use Built-under Electric double oven ContentsIntroduction SafetyInformation Safety Advice Event of a Chip PAN or ANY Other PAN FireAlways NeverThemainpartsofyour DoubleOven Thecontrols Grill Control Top OvenTop Oven Control Adjusting the Main Oven Temperature Main Oven ControlMain Oven Cooking Functions Main Oven LightConventional Heating Top Oven Variable Grilling Top OvenFan Oven Main Oven Traditional Main OvenSetting the Time of DAY Setting the Minute MinderAutomatic Cooking Hints on Automatic CookingElectronicClock&Automatic CookingFeature Auto Cooking TimerTo set the main oven to switch on and OFF immediately Cooking Duration is NOW SETCooking Duration and END Time is NOW SET SolarplusGrill This will cause overheatingGrill Pan Handle For a fixed handleFor a detachable handle To use the oven proceed as follows Do not place food or dishes on the floor Oven.GBPlatewarming in the top oven TopOvenTemperature Charts-Meat TopOvenTemperature Charts-Baking Food Pre-heat Temperature Time in mins Position in OvenCooking temperature ranges Cook chartsMainOven-TheIntelligent CookingSystem Telescopic runners and Meat panPreheat Temperature Cooking Time BakingMainOven-TheIntelligent CookingSystem Cook Chart Fish mode Pre-heat Temperature Shelf Position Cooking TimeTemperatureConversionChart MarkCare and Cleaning Top Oven Sides, Main Oven Sides Rear PanelControl Panel Inner Door Panels & GlassStainless trims UE89X1 Cleaning the Doors Drop Down DoorsRemove the door inner glass as follows Refit the door inner glass as follows Open the door fullyInstallation Final InstallationGeneral Top Top View Problem Check If something Goes wrongThere MAY be Nothing Wrong If something Goes wrong Disposal of your product Disposal of old electrical appliancesMonths Parts and Labour Guarantee Guarantee is subject to the following conditionsGuarantee does not cover Year Parts GuaranteeHotpoint Service Parts & AccessoriesUK 0870 Republic of Ireland 01 230 Xerox Business Services

UQ89I specifications

The Hotpoint UQ89I is an innovative built-in oven that exemplifies modern cooking technology, making it an excellent addition to any contemporary kitchen. This appliance combines elegance with advanced features, ensuring that users can enjoy both style and functionality.

One of the standout features of the Hotpoint UQ89I is its large capacity. With an interior volume of 71 liters, it offers ample space for cooking large meals, making it ideal for families or those who love to entertain. The oven is designed to accommodate multiple dishes at once without compromising performance, allowing for efficient meal preparation.

Equipped with a range of cooking functions, the UQ89I features traditional heating, fan assistance, and a grill option. These functions enable versatile cooking methods, ranging from baking and roasting to grilling, making it suitable for a variety of culinary techniques. The fan-assisted function ensures even heat distribution, resulting in perfectly cooked dishes every time.

One of the prominent technologies in the UQ89I is its Eco-efficient mode. This feature optimizes energy use during cooking, making it an environmentally friendly choice that reduces energy consumption without sacrificing performance. Users can enjoy delicious meals while being conscious of their energy use.

In addition to performance, ease of use is a key characteristic of the Hotpoint UQ89I. It features an intuitive digital control panel that makes it easy to select cooking modes and set timers. The oven also includes a clear LCD display, providing users with all the necessary information at a glance.

Cleaning is often a concern with traditional ovens, but the UQ89I aims to simplify this task. It is equipped with a catalytic cleaning system that utilizes specially coated walls to absorb grease and food splatter, significantly reducing the time and effort needed for maintenance.

Safety is another important consideration, and the Hotpoint UQ89I does not disappoint. It features a cool touch door, ensuring that the outer surface remains safe to touch, while an automatic shut-off function provides additional peace of mind.

Overall, the Hotpoint UQ89I is a multifunctional oven that merges style with advanced cooking technology. Its spacious design, diverse cooking functions, energy efficiency, and innovative cleaning features make it a top choice for those looking to elevate their culinary experience. With the Hotpoint UQ89I, home cooking becomes a pleasurable and efficient endeavor.
Top Page Image Contents