Installation, Very important | Hotpoint E6004 manual

Installation

These instructions are intended for the qualified technician installing the appliance in order to insure that the installation, adjustments and maintenance procedures are performed correctly and comply with the regulations currently in effect.

Important: the hob must be disconnected from the power supply before making any adjustments or performing any maintenance, etc.

Installing built-in hobs

The hob has a type X protection rating against overheating in compliance with regulation CEI 335-2-6. Therefore, the hob cannot be installed alongside of cabinets which are higher than the surface of the hob itself. The following precautionary measures should be observed in order to ensure proper installation:

a)Hoods must be installed in compliance with the required specifications contained in the instruction manual for the hood itself.

b)The built-in ceramic glass top can be installed on any counter top as long as it is 600 mm or more in width and resistant to temperatures of up to 100°C. The dimensions and the position of the hole are shown in fig..

The four securing springs are held in place by 4 Torx screws. To remove the hob unit from its housing, undo the 2 Torx screws at the front, then the 2 Torx screws at the rear.

The 4 screws should be accessible at all times for this purpose.

REAR SPRING ASSEMBLY

FRONT OF THE HOB UNIT

REAR LEFT MOUNTING
REAR RIGHT MOUNTING	WORK	30	40
	SURFACE	30	40

HOB UNIT FAST DOWN

FRONT LEFT MOUNTING

FRONT RIGHT MOUNTING

SEAL MOUNTING

FRONT / REAR

RIGHT / LEFT

560	+/-
	+/-
	1

595
	510
	1
	-
490	+/
490

Distance to keep between the cut-out slot and the cabinet

MOUSSE 5x8 mm

c)If a wooden panel is installed beneath the hob for insulation purposes, it must be positioned at least 20 mm from the bottom part of the hob itself.

Note: If the hob is installed above a built-in oven, it is preferable that the oven be installed in such a way that it is set on two strips of wood; if the oven is installed on a continuous base, there must be an opening in the back of at least 45 x 560 mm.

X (CEI 335-2-6)

These measurements must absolutely be observed in so far as improper installation can cause the surrounding surface areas to overheat. It is recommended that the hob be installed at a distance of at least 40 mm from the back wall or other vertical surfaces to ensure that the air circulates properly over the cooking area and to avoid overheating the surrounding surfaces. A seal or gasket is provided with the hob; make sure that it adheres properly to the bottom part of the frame of the hob.The seal must fit properly around the entire cooktop frame and especially along the corners in order to create a seal between the counter top and the hob itself so as to prevent spills or splashes from leaking into the cabinet below.

Very important

It is essential to instali the hob on a totally flat surtace. Any damage caused by incorrect fitting may alter the characteristics or impair performance.

Insert the hob into the hole, pressing firmly around the frame to make it adhere to the counter top.

Make certain that the seal around the outside edge of the hob is correctly installed in order to avoid any leakage into the cabinetry below.

.	45	mm.
mm		mm.
560

The built-in oven must be equipped with a forced air cooling system.

E6004 specifications

The Hotpoint E6004 is a high-performance electric cooker that epitomizes modern cooking technology and user-friendly design. Catering to both novice cooks and culinary enthusiasts, this cooker boasts a range of features that enhance cooking efficiency and convenience.

One of the standout features of the Hotpoint E6004 is its multifunctional oven. It offers a variety of cooking modes, including conventional, fan-assisted, and grill settings, allowing users to experiment with diverse recipes. The fan-assisted cooking mode ensures even heat distribution, which is essential for achieving perfectly baked cakes or roasted meats. Additionally, the integrated grill function provides a quick and efficient way to perfect browning and crisping on dishes.

The E6004 also incorporates an intuitive digital display and control panel. This user-friendly interface makes it simple to select cooking modes, set timers, and monitor temperature settings. The built-in timer feature is particularly beneficial for those who juggle multiple tasks in the kitchen, ensuring that dishes are cooked to perfection without the risk of overcooking.

A key characteristic of the Hotpoint E6004 is its energy efficiency. It comes with an A rating which indicates that it operates with minimal energy consumption. This not only helps reduce utility bills but also supports eco-friendly efforts. The cooker’s energy-saving technologies ensure that heat is retained efficiently during cooking, further decreasing energy wastage.

For safety, the Hotpoint E6004 is equipped with a robust cooling fan and a triple-glazed oven door. The fan helps to maintain a safe exterior temperature, while the triple-glazing minimizes heat loss and prevents burns when checking the cooking progress.

Cleaning the E6004 is effortless, thanks to its smooth enamel finish and easy-to-remove oven racks. This thoughtful design minimizes the accumulation of grease and food particles, allowing for quick wipe-downs after cooking.

Overall, the Hotpoint E6004 is an excellent addition to any kitchen. Its combination of advanced cooking technologies, user-friendly controls, energy efficiency, and safety features make it an ideal choice for anyone looking to enhance their cooking experience. Whether you're baking, roasting, or grilling, the Hotpoint E6004 promises to deliver consistent results and inspire culinary creativity.