Hotpoint FDEF 33121 manual Rinse aid and refined salt, Measuring out the rinse aid

Rinse aid and refined salt

GB	Only use products which have been specifically designed
	for dishwashers.
	Do not use table salt or industrial salt, or washing up liquid.
	Follow the instructions given on the packaging.
		If using a multi-functional product it is not necessary to any
	add rinse aid; however, we recommend that you add salt,
	especially if you live in an area where the water is hard or
	very hard. (Follow the instructions given on the packaging).
		If you do not add salt or rinse aid, the LOW SALT* and
	LOW RINSE AID indicator lights will remain lit.
	Measuring out the rinse aid
	Rinse aid makes it easier for the crockery to dry, as water runs
	off surfaces more readily and therefore does not leave streaks
	or marks. The rinse aid dispenser should be filled:
	• When the LOW RINSE AID* indicator light on the control panel
	is illuminated, a reserve supply of rinse aid is still available
	for 1-2 cycles;

A	X
M

1.Open the dispenser “D” by pressing and pulling up the tab on the lid;

2.Carefully introduce the rinse aid as far as the maximum reference notch of the filling space - avoid spilling it. If this happens, clean the spill immediately with a dry cloth.

3.Press the lid down until you hear a click to close it.

NEVER pour the rinse aid directly into the tub.

Rinse-aid dispenser setting

If you are not completely satisfied with the drying results, you may adjust the quantity of rinse aid.

Switch on the dishwasher using the ON/OFF button, wait a few seconds and then switch it off using the ON/OFF button. Press the Start/Pause button 3 times.

Switch on the dishwasher using the ON/OFF button, you enter the menu for setting and rinse aid indicator light shown on the display (set to factory level).

Adjust the level of rinse aid supply using the ECO cycle button. (from 0 to 4 max)

Press the ON/OFF button to save the setting.

If the rinse aid level is set to ZERO, no rinse aid will be supplied. The LOW RINSE AID indicator light will not illuminate if you run out of rinse aid.

•If there are streaks on the crockery, set the adjustment device to a lower number (1-2).

•If there are drops of water or limescale marks, set the adjustment device to a higher number (3-4).

Setting the water hardness

Every dishwasher is equipped with a water softener which, by using refined salt designed especially for this type of appliance, supplies water without limescale which is then used to wash the crockery.

This dishwasher offers a setting which helps to reduce pollution and optimises washing performance in accordance with the

water hardness level in your area. This information can be obtained from your local water supplier.

Switch on the dishwasher using the ON/OFF button, wait a few seconds and then switch it off again (ON/OFF button). Hold down the Start/Pause button for 3 seconds, switch on the dishwasher using the ON/OFF button, you enter the menu for setting and the Salt indicator light shown on the display (water softener set to medium level).

Adjust the hardness level using the ECO wash-cycle button; (from 1 to max. 5* levels.)

Press the ON/OFF button to save the setting.

Even if using multi-functional tablets, the salt dispenser should still be filled.

Water Hardness Table					Average salt container
					capacity duration**
Level	°dH		°fH	mmol/l	months
1	0	- 6	0 - 10	0 - 1	7 months
2	6 - 11		11 - 20	1,1 - 2	5 months
3	12	- 17	21 - 30	2,1 - 3	3 months
4	17	- 34	31 - 60	3,1 - 6	2 months
5*	34	- 50	61 - 90	6,1 - 9	2/3 weeks

For values between 0°f and 10°f, we do not recommend the use of salt. * this setting may cause a slight increase in the duration of the cycles. ** for 1 wash cycle per day.

(°dH = hardness measured in German degrees - °f = hardness measured in French degrees – mmol/l = millimoles per litre)

Measuring out the refined salt

In order to obtain the best possible results from a wash cycle, make sure that the salt dispenser is never empty.

Refined salt removes limescale from the water, thus avoiding the formation of deposits on crockery.

The salt dispenser is located in the lower part of the dishwasher (see Description) and should be filled:

•When the green float* cannot be seen by simply looking at the cap of the salt dispenser;

•When the LOW RINSE AID indicator light on the control panel

is illuminated *;

1. Remove the lower rack and unscrew the cap (anticlockwise).

2.The first time you do this: fill the water tank right up to its edge.

3. Position the funnel* (see figure) and fill the salt dispenser up to the edge (approximately 1 kg). It is normal for a little

water to leak out.

4.Remove the funnel* and wipe any salt residues away from the opening; rinse the cap under running water and then screw it on, the head facing downwards so as to let the water flow out

of the four slots (star-shaped) on the lower part of the cap (cap with green float*).

It is advisable to perform this procedure every time you add salt to the dispenser.

Make sure the cap is screwed on tightly so that no detergent can get into the container during the wash cycle (this could damage the water softener beyond repair).

When necessary, measure out the salt before a wash cycle so that any saline solution which has leaked out of the salt dispenser is removed.

*Only available in selected models.

14