Hotpoint DQ891 manual Installation

Page 24

Installation

Electrical Requirements

GB For your own safety, we recommend that your cooker is installed by a competent person such as one who is registered with NICEIC (National Inspection Council for Electrical Installation Contracting). The cooker should be installed in accordance with the latest edition of the IEE Regulations.

Warning: This appliance must be earthed.

Electrical Connections

The installer must check that the voltage shown on the rating plate corresponds with the house electricity supply. The cooker must be supplied via a suitable double pole isolating switch, having a contact separation of at least 3mm in all poles placed in a readily accessible position adjacent to the cooker. If the cooker is to be wired into a connector unit, this may be positioned behind the cooker providing the following requirements are met:

i)The connector unit must not project from the wall more than 25mm.

ii)The top of the connector must not be more than 130mm above floor level.

Remove the terminal cover at the rear base of the cooker. Pass the cable through the cable clamp and connect to the appropriate terminals provided. Allow sufficient cable for any future servicing. Tighten the screws on the cable clamp and replace the cover. Make main connections in the connector unit or cooker control unit. This appliance conforms to B.S. EN 55014 regarding suppression of Radio and Television reception interference.

A double Pole control switch having a minimum rating of 32 amps should be used to feed the cooker using a suitably rated cable. Where a hob is fitted adjacent to or over the cooker, a 45 amp Double Pole control switch should be used to feed both units via separate suitably rated cables.

We recommend a minimum of 4mm2 PVC insulated twin and earth cable conforming to B.S. 6004 for connection of each appliance.

In all cases adhere to routing details (see fig. 4).

This appliance must not be installed over any other appliance that generates heat such as a plinth heater.

Note: Due to many different types of installation, a mains cable is not supplied with this product. The installer will fit the correct type and length of cable.

Important

It is essential that the lower cupboard is constructed in the manner illustrated i.e. having side, back, and roof panels so joined as to provide no apertures which could permit access to the oven unit when installed.

1. General

The appliance is designed for mounting at a safe level into an oven housing which must be secured to the backing wall.

2. Ventilation

a.The oven housing unit cabinet dimensions must comply with fig. 4.

b.An air gap of 50mm minimum must be provided at the rear of any top or bottom cupboards or shelves (see fig. 1).

c.It is necessary that the cabinets are provided with unobstructed ventilation, i.e. from adjacent cabinetry. This can be done by either raising the base of the cabinets using the adjusting feet (or spacers) or alternatively by providing a slot in the cabinet plinth to the dimensions in fig. 1.

d.The air gap at rear allows the warmed air to pass out of the inner cabinet space. Where it is intended to fit cupboards above the oven unit to ceiling height, it is essential that the warmed air is exhausted through the front of the cabinet (see fig. 1).

e.If an oven unit is installed adjacent to a tall cabinet, steam escaping from the oven when the door is opened could condense on and maybe stain the adjacent surface. To prevent permanent staining, the adjacent surface should be made of a material that is heat resisting and easy to clean. Adjacent tall cabinets should not be deeper than the oven housing cabinet.

3. Final Installation

a.Using a spirit level, check that the housing cabinet is level from side to side and from front to back in its installed position.

b.Correct any unevenness by placing spacers under the bottom of the cabinet. Make sure that the cabinet rests firmly on the floor without rocking.

c.Before the oven is fitted, the cabinet must be firmly secured to the backing wall for stability.

d.The oven unit should now be lifted (this is a two person lift) into the cabinet and pushed fully home.

e.Finally, the oven is secured to the cabinet by means of the four Phillips C/SK Head screws - two through each side trim.

f.Remove all packaging material from the grill and oven interior.

List of loose items:

4 x Phillips C/SK Head No. 6 x 25mm screws.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Instructions for Installation and Use Build-in Electric double oven ContentsIntroduction SafetyInformation Safety Advice Event of a Chip PAN or ANY Other PAN FireAlways NeverThemainpartsofyour DoubleOven Thecontrols Grill Control Top OvenTop Oven Control Adjusting the Main Oven Temperature Main Oven ControlMain Oven Cooking Functions Main Oven LightLower Temperature Main Oven Model AHP67 only Conventional Heating Top OvenVariable Grilling Top Oven Fan Oven Main OvenSetting the Time of DAY Setting the Minute MinderAutomatic Cooking Hints on Automatic CookingElectronicClock&Automatic CookingFeature Auto Cooking TimerTo set the main oven to switch on and OFF immediately Cooking Duration is NOW SETCooking Duration and END Time is NOW SET SolarplusGrill This will cause overheatingGrill Pan Handle For a fixed handleFor a detachable handle To use the oven proceed as follows Do not place food or dishes on the floor Oven.GBPlatewarming in the top oven TopOvenTemperature Charts-Meat TopOvenTemperature Charts-Baking Food Pre-heat Temperature Time in mins Position in OvenCooking temperature ranges Cook chartsTelescopic runners and Meat pan Preheat Temperature Cooking Time BakingMainOven-TheIntelligentCooking System Cook Chart Fish mode Pre-heat Temperature Shelf Position Cooking TimeMainOven-TheIntelligent CookingSystem TemperatureConversionChart MarkCare and Cleaning Top Oven Sides, Main Oven Sides Rear PanelControl Panel Inner Door Panels & GlassCleaning the Doors Drop Down DoorsRemove the door inner glass as follows Refit the door inner glass as follows Open the door fullyInstallation Tall Cabinet Ventilation 595mm Problem Check If something Goes wrongThere MAY be Nothing Wrong If something Goes wrong Disposal of your product Disposal of old electrical appliancesMonths Parts and Labour Guarantee Guarantee is subject to the following conditionsGuarantee does not cover Year Parts GuaranteeHotpoint Service Parts & AccessoriesUK 0870 Republic of Ireland 01 230 Xerox Business Services

DQ891 specifications

The Hotpoint DQ891 is a sophisticated and versatile dishwasher that combines modern design with innovative technology to enhance your kitchen experience. As part of Hotpoint's commitment to high performance and efficiency, the DQ891 stands out with its robust features, tailor-made for busy households.

One of the key highlights of the Hotpoint DQ891 is its impressive capacity. With a spacious interior that accommodates up to 15 place settings, this dishwasher is perfect for families or those who frequently entertain guests. The adjustable racks and foldable tines provide flexibility, allowing users to optimize the space based on their specific needs. Whether you are washing delicate glassware or bulky pots and pans, the DQ891 can handle them with ease.

The technology integrated into the DQ891 ensures a deep clean while being gentle on your dishware. The unique Hydroclean technology utilizes a high-pressure water system that effectively removes stubborn food residues, even from hard-to-reach areas. Additionally, the Energy Saver cycle allows users to choose eco-friendly settings, reducing water and energy consumption without compromising cleaning performance, achieving an excellent A++ energy rating.

When it comes to user-friendliness, the Hotpoint DQ891 doesn’t disappoint. The intuitive control panel features clearly labeled buttons and a digital display that provides vital information, including cycle time and remaining duration. With multiple wash programs ranging from quick washes to intensive cleaning, users have the flexibility to select the perfect cycle based on their needs. The Delay Start option also allows for customization, enabling the dishwasher to run at a time most convenient for the user.

Noise levels are often a concern with dishwashers, but the DQ891 operates quietly, thanks to its advanced sound insulation. This makes it suitable for open-plan living spaces where noise can be disruptive.

In summary, the Hotpoint DQ891 combines practical design, powerful cleaning technology, and user-friendly features. With its spacious capacity, energy-efficient settings, and quiet operation, it promises a seamless dishwashing experience, making it an excellent addition to any modern kitchen. Whether you’re looking to save time or improve your cleaning routine, the DQ891 is engineered to meet the demands of contemporary living.
Top Page Image Contents