Wells MOD-427TDMAF, SS-10ULTD, BMW-206RTD Electrical Installation, Plumbing Installation

Page 7

011 303308 OpManual for Built-In T’Stat Warmers

5.For “top-mounted” warmers (i.e. warmers mounted from above the counter top):

a.Verify that provided sealants are applied to the underside of the warmer top flange prior to setting the unit into the cutout.

b.After installation, verify that the tabs on the Wellsloks are turned out to lock the warmer into the counter

c.Apply a thin bead of food-grade silicone sealant around the flange to seal it to the counter.

d.Wellslok extension kits are available for installing warmers in counter tops where the standard Wellslok would not normally reach. The extension kit will adapt to counter tops up to 1¾” thick.

ELECTRICAL INSTALLATION

1.Refer to the product nameplate. Verify the electrical service power. Voltage and phase must match the nameplate specifications. Wiring the warmer to the wrong voltage can severely damage the unit or cause noticeably decreased performance.

2.Available electrical service amperage must meet or exceed the specifications listed on the specification sheet provided with the warmer.

3.Warmer and control unit must be connected to an appropriate building ground. Ground connection will be marked “GND” or ” " .

NOTE: Wire gauge, insulation type and temperature rating , as well as type, size and construction of conduit, must meet or exceed applicable specifications of local codes and of the National Electrical Code.

E. PLUMBING INSTALLATION

For use in the State of Massachusetts, this appliance must be installed in compliance with Massachusetts Fuel Gas and

Plumbing Code CMR 248.

1.IMPORTANT: All plumbing installations must be performed by a qualified plumber.

2.For units equipped with a DRAIN LINE: Some jurisdictions may require an approved air gap or other back-flow prevention device in the drain. It is the responsibility of the plumber to determine such requirement, to provide and properly install the required device.

3.For SS-4, SS-8 and SS-10 drainline units, the drain must be attached with a union at the drain line fitting. This is necessary to provide for future maintenance of the heating element.

4.For AUTOFILL units: Some jurisdictions may require an approved back-flow preventer in the water supply line. It is the responsibility of the plumber to determine such requirement, and to provide and properly install the required device.

Autofill supply must be connected to a COLD WATER line only.

5

NOTE: Damage caused by leaks due to improper installation is NOT covered by warranty.

CAUTION:

SHOCK HAZARD

The ground lug of this appliance must be connected to a suitable building ground.

IMPORTANT:

Contact a licensed electrician to install and connect electrical power to the appliance.

IMPORTANT: Damage due to being connected to the wrong voltage or phase is NOT covered by warranty.

IMPORTANT: Electrical installation other than as specified on the specification sheet will void the UL listing, and may void the warranty.

NOTE: Plumb connections must be made in compliance with all Federal, State and Local Plumbing Codes and Ordinances.

Image 7
Contents Wells BUILT-IN Warmers 011 303308 OpManual for Built-In T’Stat Warmers Introduction Autofill ThermostatMounting DrainsAgency Listing Information 011 303308 OpManual for Built-In T’Stat Warmers Plumbing Installation Electrical InstallationOperation PRE-HEATING the Warmer011 303308 OpManual for Built-In T’Stat Warmers Burn Hazard Chemical Burn Hazard Weekly Cleaning InstructionsSymptom Possible Cause Suggested Remedy Care of Stainless Steel Description Adapters & Insets Important Use only factory authorized service parts Genuin e Parts

BMW-206RTD, MOD-427TDMAF, SS-10ULTD specifications

The Wells SS-10ULTD, MOD-427TDMAF, and BMW-206RTD are notable products in their respective fields, offering advanced features and cutting-edge technologies that set them apart in the market.

The Wells SS-10ULTD is a state-of-the-art coolant chiller designed for heavy-duty industrial applications. It boasts a robust construction, ensuring durability and efficient operation even in the most demanding environments. One of its main features is its innovative heat exchange technology that maximizes cooling performance while minimizing energy consumption. The unit is equipped with an intuitive control system that allows users to monitor and adjust settings easily, ensuring optimal performance tailored to specific needs. With its sophisticated safety features, including overload protection and temperature regulation, the SS-10ULTD delivers reliable operation and peace of mind for operators.

On the other hand, the MOD-427TDMAF is a versatile and powerful data management tool that caters to the needs of modern businesses. This device integrates advanced data processing capabilities with user-friendly software, enabling seamless management of large datasets. Key features include real-time data analysis, allowing businesses to extract actionable insights and make informed decisions quickly. The MOD-427TDMAF also supports multiple connectivity options, making it compatible with a wide range of devices and systems. Its scalable architecture ensures that it can grow with a business's evolving requirements, making it a smart investment for organizations aiming to enhance their data handling processes.

Lastly, the BMW-206RTD is a highly regarded motorcycle that combines performance with style. This model is renowned for its powerful engine that delivers an exhilarating ride, paired with advanced suspension technology that ensures smooth handling and comfort on various terrains. One of its standout features is the integration of cutting-edge safety systems, including anti-lock braking and traction control, providing riders with added security. The BMW-206RTD also showcases an ergonomic design with user-friendly controls, making it accessible for riders of all skill levels. With its striking aesthetics and robust performance, this motorcycle appeals to enthusiasts looking for both functionality and flair.

In summary, the Wells SS-10ULTD, MOD-427TDMAF, and BMW-206RTD exemplify excellence in their respective domains, offering a blend of innovative technologies and practical features that enhance overall user experience and operational efficiency.