Bush XDNX1V1KC manual Convertible, Pickup Truck

Page 18

Vehicle Installation

the carpet toward the dashboard or console.. Coil any excess cable in a hidden location, such as under the carpet, keeping it away from any vehicle pedals or controls.. Secure the excess cable with wire ties (purchased separately)..

4.Bring the end of the cable out at the PowerConnect Vehicle Dock location.. Leave yourself enough cable so you can easily connect it to the antenna connector of the dock..

5.Continue with “Step 5: Connect the Magnetic Mount Antenna and PowerConnect Power Adapter” on page 37..

Convertible:

1.Bring the antenna cable from the antenna into the trunk at the front edge of the trunk lid.. Keep any bends in the cable loose.. Tape or tie the cable along the inside of the trunk lid to the trunk lid hinge strut..

2.Allow enough slack in the cable so the trunk lid can easily open and close and keep the cable away from hinges, gears, etc.., that could crimp or cut it.. Route the cable

along the trunk wall and into the cabin through a conduit or along an existing wiring harness..

3. Route the cable through the main cabin area under the interior trim, towards the front of the vehicle..

Use a blunt plastic putty knife or similar blunt tool to lift the plastic trim just enough to tuck the cable

under underneath.. Avoid side airbag locations on back pillars and above the doors.. Airbag locations are marked with “SRS” logos.. Be careful not to crimp or cut the cable..

4.Bring the cable out from the trim near the front of the cabin and route it under the carpet toward the dashboard or console.. Coil any excess cable in a hidden location, such as under the carpet, keeping it away from any vehicle pedals or controls.. Secure the excess cable with wire ties (purchased separately)..

5.Bring the end of the cable out at the PowerConnect Vehicle Dock location.. Leave yourself enough cable so you can easily connect it to the antenna connector of the dock..

6.Continue with “Step 5: Connect the Magnetic Mount Antenna and PowerConnect Power Adapter” on page 37 ..

Pickup Truck:

1.Use a blunt plastic putty knife

or similar blunt tool to lift the rubber molding around the windshield and tuck the antenna cable underneath it..

2.Continue tucking the cable underneath the windshield molding around the windshield to the lowest corner..

3.At the lowest corner of the

34

35

Image 18
Contents User Guide Table of Contents Introduction Please read the entire user guide before using your onyX FeaturesSafety and Care Information IntroductionPowerConnect Vehicle Dock What’s in the Box?OnyX Functions PowerConnect Vehicle Dock Colour-Coded ConnectionsVehicle Installation Wire GuideVehicle Installation Choose a Location for Your RadioInstall the Dash or Vent Mount Installing the Dash MountInstalling the Vent Mount To install the Magnetic Mount Antenna Mount the Magnetic Mount AntennaPickup Truck We recommend Vehicle Installation Route the Magnetic Mount Antenna Cable Route cable along trunk wall and into cabin Vehicle Installation Sedan/Coupe With Antenna Placed at the Rear of the Roof Sedan/Coupe With Antenna Placed at the Front of the Roof SUVConvertible Pickup TruckAudio ANT PWR Option 1 Aux In Cable Installation Instructions Connect the AudioOption 2 Cassette Adapter Installation Instructions Option 3 PowerConnect Installation Instructions 90.1 Option 4 FM Direct Adapter Fmda Installation 99.3 FMActivation Using Your onyX ActivationUsing Your onyX Main DisplayNavigation Basics Listening to Satellite Radio Tune a channelView a category Jump Direct TuneDirect Tune Return to Main Display ScreenFavorite Saved Favourite ChannelsScanning Channels in a Category FM Presets To start using a different FM preset103.7 FM Special Features Trim Rings Special FeaturesColour Themes To change the colour themeMenu 3287 Parental ControlsTo turn Parental Controls On or Off Select button To lock or unlock channels or categoriesTo change your code To listen to a locked channel To select a locked channel from the category listWhere Else Can You Use Your onyX? Configuring Your onyX Where Else Can You Use Your onyX?Radio ID Configuring Your onyXA234B456 Find Available FM Channels in Your AreaConfiguring Your onyX 97.9 To set and select an FM presetSet and Select an FM Channel 103.7To quickly select an FM channel from the preset list 99.3 FMTo configure jump Jump SettingsAtlanta Mode Baltimore Set LocationSet Audio Level To adjust the audio levelSet Brightness To change the display’s brightnessRestore Defaults Signal IndicatorFactory Settings AUX DetectTo reset onyX to factory defaults Disable AUX Detect?Restore Defaults To enable AUX DetectDemo Mode Status enabled Enter Demo ModeTo enable or disable the demo mode Using the Vehicle Dock From the Universal Xpress Car Kit If you are connecting the audio using PowerConnect or FmdaFM Transmitter on FM Channels Turn FM Transmitter On/OffFM Transmitter off FM Channels Turn OFF FM?Troubleshooting Troubleshooting Try this104 105 Product Specifications Patent Information Product SpecificationsPatent and Environmental Information Environmental InformationFCC and IC Statement Copyrights and TrademarksOwners Record Owner’s RecordXDNX1V1KC

XDNX1V1KC specifications

Bush XDNX1V1KC is a modern television that combines sleek design with advanced technology to enhance your viewing experience. This model has garnered attention for its impressive features and user-friendly interface, appealing to a broad range of consumers.

One of the standout characteristics of the XDNX1V1KC is its display quality. The television boasts a high-resolution LED screen that delivers vibrant colors and sharp contrasts, making it perfect for watching movies, playing video games, or enjoying live sports. The screen size options cater to various room sizes, ensuring that users can find the perfect fit for their home.

The television incorporates advanced technologies to optimize image quality. With features such as 4K Ultra HD resolution and HDR (High Dynamic Range), the Bush XDNX1V1KC is capable of rendering stunning visuals with remarkable detail and a broader range of brightness levels. This technology allows viewers to experience content as the creators intended, bringing out the nuances in each scene.

In addition to remarkable picture quality, the Bush XDNX1V1KC is equipped with smart TV capabilities. The integrated smart platform provides access to a wide array of streaming services, giving users the convenience of watching their favorite shows and movies directly from their television without needing additional devices. Navigation is seamless thanks to a user-friendly interface that allows for easy access to various applications.

Another appealing element of the XDNX1V1KC is its connectivity options. The television is equipped with multiple HDMI and USB ports, enabling users to connect a variety of devices, such as gaming consoles, Blu-ray players, or sound systems. Furthermore, built-in Wi-Fi allows for easy internet connectivity, enhancing the TV's smart features.

Audio performance is also an essential aspect of the Bush XDNX1V1KC. The television features an integrated sound system designed to produce clear and dynamic sound. For those desiring an immersive audio experience, the TV supports external audio systems for enhanced sound quality.

In conclusion, the Bush XDNX1V1KC combines cutting-edge display technology, smart features, and versatile connectivity to create a well-rounded television option. It is designed to cater to the needs of modern viewers, making it an excellent choice for anyone looking to elevate their home entertainment experience. Whether you're a movie buff, a gaming enthusiast, or a casual viewer, this television is poised to meet your demands and exceed expectations.