Acnodes FPC 8084 user manual Set Supervisor/User Password, Enter Password

Page 64

FPC 8084 User’s Manual

A.2.11 Set Supervisor/User Password

Either supervisor or user password, or both of them can be set in this option. The differences between them are:

1.supervisor password: can enter and change the options of the setup menus.

2.user password: just can enter but do not have the right to change the options of the setup menus.

When this function is selected, the following message will appear at the center of the screen for creating a password.

ENTER PASSWORD:

Type the password with eight characters at most, and press <Enter>. The password typed will now clear any previously entered password from CMOS memory. Then, confirm the password by typing the password again and pressing <Enter>. Or, not enter a password and abort the selection by pressing <Esc>.

To disable the password by pressing <Enter> without typing in any password when the message “Enter Password” is showed. Then, message below will appear to confirm that the password has been disabled.

PASSWORD DISABLED.

Once the password is disabled, the system will boot and enter Setup freely.

When a password is enabled, it has to be typed to enter the Setup every time. This prevents any unauthorized person from changing the system configuration.

Additionally when a password is enabled, the BIOS can also set to request a password every time the system reboots. This would prevent unauthorized use of the computer.

The user can determine when the password is required within the BIOS Features Setup Menu and its Security option. If the Security option is set to “System”, the password is required during boot up and entry into Setup. If it set as “Setup”, prompting will only occur prior to entering Setup.

62

Page 63 Page 65
Image 64
Page 63 Page 65
Contents FPC All-in-One Super SlimDisclaimers Safety Approvals Safety Precautions Trademarks Acknowledgments This page does not contain any information Table of Contents A p t e r Embedded O.S. Installation Introduction General DescriptionMain CPU Board Specifications2 I/O System System Specification 100W DC power supplyDimensions I/O Outlets Package List A p t e r Hardware Installation HDD InstallationFix the HDD bracket kit to system by 4 screws CF card Installation Add-on Card Installation Set the bracket to protect COM Port Connector COM1 3 x Serial PortsRS-232 pin assignments are listed on the following table VGA Ethernet PJ-45 Connector LAN1Ethernet Mountings Panel / Wall / Desktop VESA-ARM/Wall-MountDesktop Kit Assembly Panel-mount Kit Assembly Specification Touch ScreenDriver Installation- Windows 98/2000/XP/CE.NET/XP-Embedded PenMount Control Panel Select the Standard Calibrate tab Identify the communication port and IRQ Number Do CalibrationInitializing the PenMount driver Driver Installation- Linux Advance SetupDemonstration Install PenMount driver GOT-1840T User’s ManualDo Calibration Windows XP Embedded Penmount Touch ScreenOnboard Multi I/O Onboard IDEWindows CE.NET Calibration Touch ScreenBios Introduction 2BIOS SetupPhoenix Aw ardBIOS Cmos Setup Utility Standard Cmos Setup AugFPC 8084 User’s Manual Date TimeDrive a type/Drive B type Select Display DeviceLCD Type Display Type During PostHalt On Advanced Bios Features HDD-0Processor Number Feature Quick Power On Self TestFirst/Second/Third Boot Device Boot Other DeviceBoot Up Floppy Seek Boot Up NumLock StatusTypematic Rate Setting Swap Floppy DriveTypematic Delay Msec Typematic Rate Chars/SecSecurity Option OS Select for Dram 64MBVideo Bios Shadow C8000 Cbfff Shadow/DC000 Dffff ShadowAdvanced Chipset Features 16MAGPSystem Bios Cacheable Dram Timing By SPDDram Clock Sdram Cycle LengthPCI Delay Transaction PCI#2 Access #1 RetryUSB Keyboard Support CPU to PCI Write BufferThis option sets the hard disk configuration, mode and port Integrated PeripheralsIDE Prefetch Mode IDE HDD Block ModeOn-Chip IDE Channel0/Channel1 Primary/Secondary Master/Slave PIOUart 2 Mode TX,RX inverting enableOnboard Parallel Mode ECP Mode Use DMAFPC 8084 User’s Manual Power Management Setup Power ManagementAcpi Function PM Control by APMVideo Off Option Video Off MethodModem Use IRQ Soft-off by PwrbtnFPC 8084 User’s Manual PNP OS Installed 6 PNP/PCI ConfigurationReset Configuration Data Resource controlled by IRQ ResourcesDMA Resources PCI/VGA Palette SnoopPC Health Status 5V/3.3V/5V/12VAuto Detect DIMM/PCI Clk Frequency/Voltage ControlSpread Spectrum Load Fail-Safe Defaults Phoe nix Award Bios Cmos Setup UtilityLoad Optimized Defaults Load Optimized Defaults Y/N? NSet Supervisor/User Password Enter PasswordSave & Exit Setup Save to Cmos and Exit Y/N? YExit Without Saving Quit Without Saving Y/N? N

FPC 8084 specifications

The Acnodes FPC 8084 is a state-of-the-art embedded computer system designed for rigorous industrial applications and demanding computing environments. Built with advanced technologies that prioritize reliability and performance, the FPC 8084 is ideal for sectors such as automation, transportation, and telecommunications.

One of the key features of the FPC 8084 is its robust design. The system employs a fanless operation, which ensures silent performance while minimizing the risk of dust and debris infiltration, making it suitable for environments where traditional cooling solutions may be ineffective. This characteristic not only enhances its lifespan but also reduces maintenance costs.

The FPC 8084 is powered by Intel's powerful processors, which offer high computational capabilities and energy efficiency. The inclusion of multiple cores allows for better multitasking and responsiveness, vital for operations that require real-time data processing. Additionally, the system supports a range of operating systems, including various versions of Windows and Linux, providing users with flexibility in software utilization.

Moreover, the FPC 8084 is designed with an array of I/O options, including USB, COM ports, and Ethernet interfaces. This extensive connectivity enables seamless integration into existing system architectures and simplifies communication with other devices. For applications that require expansion capabilities, the FPC 8084 offers PCIe slots, allowing users to add custom cards as needed.

In terms of storage, the FPC 8084 incorporates advanced technology for robust data handling, supporting both SSD and HDD options. This ensures fast access times and ample space for large datasets, which is crucial for data-intensive applications. Furthermore, the system comes equipped with various security features to protect sensitive information, including TPM (Trusted Platform Module) support.

Another significant characteristic of the Acnodes FPC 8084 is its wide operating temperature range. Designed to function optimally in extreme conditions, this feature makes it particularly suitable for outdoor or environmentally challenging installations. Coupled with its durable construction, the FPC 8084 stands as a reliable choice for enterprises seeking a trustworthy embedded computing solution.

In summary, the Acnodes FPC 8084 is a versatile and powerful embedded system that combines advanced technology with durable design. Its fanless operation, extensive connectivity options, and ability to withstand harsh environments make it a top choice for various industrial applications. With Acnodes' commitment to quality and innovation, the FPC 8084 is poised to meet the needs of businesses seeking dependable computing solutions.
Top Page Image Contents