Black & Decker DCM2160W manual How to Use

How to Use

This product is for household use only.

GETTING STARTED

1.	Remove all packing material, and any stickers from the product.
2.	Remove and save literature.

12:00 POWER

F

SETTING THE CLOCK

1.Plug appliance into standard electrical outlet.

2.The digital clock display flashes 12:00 (F).

Note: You must set the clock in order to use the Delayed Brewing feature.

3. Wash all removable parts as instructed in the Care and Cleaning section.

	4. Open water reservoir/brew basket cover and pour in
C
	fresh cold water up to the #12-cup level mark. Caution:
	Be careful not to exceed the 12-cup maximum level, to
	avoid water running out the overflow hole in the back
	of the coffeemaker (C).

G

POWER

3.To set the time: Press HOUR button until the correct hour appears (G).

Note: When the time passes Noon a small light appears in the top left corner of the digital display under the PM signage to let you know you are in P.M. time. If the P.M. indicator is not lit, the time is A.M.

5. Place empty 8 to 12 cup basket style paper filter into

removable filter basket.

6.Place basket into brew basket with the handle to the right (D).

D

7.Close water reservoir/brew basket cover securely.

8.To replace brew-thru lid cover on empty carafe insert small hole on left side of cover handle into projection on carafe cover holder. Press U-shaped projection on right

		4. Repeat with the MIN button (H). (If minute setting is not
H
		changed within 5 seconds, the clock will revert to default
	PO	time and the selection of hour and minute will have to
		be repeated.)

Tip: Hold the button down to make the hours and minutes change rapidly after a short delay. To change the time in 1 minute increments, press and release the MIN button.

Note: If the unit is unplugged or power is interrupted even momentarily, the time will need to be reset.

BREWING COFFEE

It is not necessary to set the clock to brew coffee unless you want to use Delayed Brewing.

	side of cover handle down to click into position on right
E	side of cover holder (E).

9. Place empty carafe on the “Keep Hot” plate.

10. Pull power cord out from power cord holder in back of coffeemaker and plug

into standard electrical outlet.

11. Brew water through appliance following the “Brewing Coffee” instructions

without adding coffee grounds. This removes any dust or residue that may

J

X

MA

1.Open water reservoir/brew basket cover.

2.Fill water reservoir with cold tap water up to the desired water marking on the side of reservoir. Caution: Be careful not to exceed the 12-cup maximum level, to avoid water running out the overflow hole in the back of the coffeemaker (J).

have remained in the coffeemaker during the manufacturing process.

12. When brewing is complete, discard the water from the carafe and paper filter

from filter basket.

13. Turn off the coffeemaker; unplug it and allow it to cool down.

ADJUSTING THE POWER CORD LENGTH

•You can adjust the length of the power cord to suit your needs.

•To increase the length of the power cord, simply grasp the cord (not the plug) in the rear of the coffeemaker and gently pull down and out of the slot away from the coffeemaker.

•To decrease the length of the power cord, simply feed any excess cord into the slot in the rear of the coffeemaker.

•Lift the cord and lock it into the slot when cord is at desired length.

3.Place an 8 to 12 cup basket style paper filter in the removable filter basket, make sure that it is properly centered in the brew basket.

4.Add your desired amount of ground coffee.

5.Insert brew basket into brew basket holder following directions in GETTING STARTED.

6.Close brew basket/ water reservoir cover securely.

7.Place brew- thru cover on empty carafe following directions in GETTING

STARTED.

Note: Coffee may overflow if brew-thru lid is not properly aligned.

8.Place empty carafe on the “Keep Hot” plate.

9.Plug cord into standard electrical outlet.

5 6