Euro-Pro EP585 owner manual Operating Instructions, Assembling the Hand Mixer to, Stand

Read all the sections of this booklet and follow all the instructions carefully.

OPERATING INSTRUCTIONS

OPERATING INSTRUCTIONS

Assembling the Hand Mixer to

3. While the hand mixer is still in the

raised position, insert either the

Warning: To avoid injury when inserting or removing beaters or

dough hooks, always set the speed selector on “0” and unplug the appliance.

1.Before using your Convertible Hand/Stand Mixer for the first time, wash the beaters, dough hooks, bowls and spatula in warm, sudsy water. Rinse and dry thoroughly. Use a damp cloth to wash over the mixer base and the hand mixer. Dry with a soft cloth. NEVER immerse the base stand or the hand mixer in water or any other liquids.

2.Before assembling your Convertible Hand/Stand Mixer, make sure that the power cord is unplugged from the electrical outlet and that both the speed control and the base speed control dial are in the “OFF” position.

Attaching the Beaters to the Hand Mixer

1.Ensure that the hand mixer is not plugged in to an electrical outlet and that the speed control switch is on the “0” (off) position.

2.Insert the beaters into the sockets on the under side of the hand mixer and twist counter clockwise until the beater is firmly fitted into the socket.

3.To release the beaters from the unit, press on the beater eject button on the front of the unit and they will pop out. (Fig. 1)

Press

eject

button

Fig. 1

Attaching the Dough Hooks to the Hand Mixer

1.Ensure that the hand mixer is not plugged in to an electrical outlet and that the speed control switch is on the “0” (off) position.

2.The dough hooks have a set method of fitting into the hand mixer because they are not identical. One has a grommet and the other does not. (Fig. 2)

Grommet

Fig. 2

3.Looking at the under side of the hand mixer, you will see that one of the sockets has a red dot over it. (Fig. 3) Insert the dough hook with the grommet into this socket.

Grommet

Fig. 3

4.Then insert the other dough hook into the other socket. Push both dough hooks in until you hear a click confirming that they are securely in place.

5.To release the dough hooks from the unit, press on the beater eject button on the front of the unit and

they will pop out. (Fig. 1) Note: Ensure that the beaters or dough hooks are fully inserted into the correct sockets or your mixing results may be affected.

the Stand

Warning: To avoid injury when assembling the hand mixer to the stand, always set the speed selector on

“0” and unplug the appliance.

1.Press the tilt button, located on the top of the support pivot . While the button is depressed, ease the support pivot back. (Fig. 4)

Tilt Button

Support

Pivot

Fig. 4

The support pivot will lock into this raised position until it is released by pressing the tilt button again.

2.To connect the hand mixer to the support pivot, locate the two retaining prongs on the support pivot into the two rectangular holes in the heel of the hand mixer. (Fig. 5) When the hand mixer is seated on the support pivot, press down on the hand mixer to click it into place and lock the hand mixer and the support pivot together.

Rectangular

holes

Support

Retainingpivot prongs

Fig. 5

Note: Ensure that the two retaining prongs on the support pivot are fully connected into the hand mixer.

beaters or the dough hooks.

4. To lower the hand mixer, press and

hold the tilt button with one hand

while holding the hand mixer with the

other hand and slowly lower the hand

mixer down. (Fig. 6)

Press the tilt button and tilt the hand mixer down

Fig. 6

5.To remove the hand mixer from the pivot support, first raise the mixer by pressing the tilt button and raise the mixer up. (Fig. 7) the mixer will lock into the raised position.

6.Then press the mixer release button which is located on the under side of the pivot support with one hand and with the other lift the hand mixer by the handle upwards and away from the support pivot. (Fig. 8)

Press the tilt button and tilt the hand mixer up

Fig. 7

Hand mixer release button

Fig. 8

3 4