Specifications, Details and Dimensions | Hobart CG10FI specification

CG10FI GAS

FULL SIZE COMBI OVEN

701 S Ridge Avenue, Troy, OH 45374

1-888-4HOBART • www.hobartcorp.com

SPECIFICATIONS:

General: Hobart Combi Oven, gas steam generator, 10 level full size combi.

Construction: All stainless steel interior and exterior. Top, rear, sides, and bottom are fully insulated. All welded stainless steel cooking compartment. Stainless steel oven door features a large curved outer glass with enhanced insulation for a cool to touch exterior, with full length hinged floating inner glass panel. A full perimeter door gasket with drip tray inside door and oven frame. Door opens right to left and swings a full 180 degrees. Standard with rack guides and (5) wire racks. Built in wash arm for automatic cleaning with auto dosing pump, 4-speed auto reversing fan,

(3)halogen flashing door lights, core probe, dual point door latch connection for a full perimeter sealed connection. Standard with 1.6" feet for stand connection.

Controls: Simple, user friendly digital controls on the right with large, low voltage LCD display - for easy cleaning and operating

pleasure. Manual operation or programmable up to 100 recipes with 10 cooking phases each. Includes Bluetooth® communication and recipe software for PC.

Operation: Hobart’s gas pressureless steam generator and open burner in the cooking cavity uses optimized cooking functions and engineering technology for maximum production with minimal

energy and water consumption.

Electrical: 120/60/1 (cord and plug by others).

Gas: 60,000 BTU’s, 3⁄4" gas connection NPT.

Water: A suitable Hobart Water Treatment System is the recom- mended minimum to meet the water quality spec. 3⁄4" NSHT cold

water, 30-60 psi and 1" NPT drain connection .

Capacity: Capable of holding: (20) 12" x 20" x 21⁄2" steam table pans or (10) 18" x 26" x 1" sheet pans or (20) 13" x 18" x 1" half size sheet pans.

DETAILS AND DIMENSIONS:

Model

Width

Depth

Height

Weight

CG10FI

35.4"

45.0"

36.8"

437 lbs.

LEGEND:

1.GAS

2.DRAIN

3.ALTERNATE DRAIN

4.WATER SUPPLY

5.ELECTRIC

Gas Presure: A regulator sized for this unit is included. Natural gas 5" W.C., propane gas 10" W.C. supply pressure.

Clearance: Left 1", Back 2", Right 2" required, 18" recommended for service access.

Model	Electrical	Gas*
CG10FI	120/60/1	60,000 BTU

NOTES:

Amperage values in the table are nominal. Tolerance is +5/-10%. * Natural gas. Values rounded to 1,000. Maximum usage shown.

User Responsibility: The product must be installed, cleaned and maintained as described in the Manual furnished with the product.

Water Quality Specification for Warranty Purposes

The fact that a water supply is potable is no guarantee that it is suitable for steam generation. All steam equipment is subject to contamination and failure due to chemical and mineral content found in water. A suitable Hobart Water Treatment System and regular filter replacements coupled with routine deliming is the recommended minimum. Damage as a result of poor water quality or lack of required owner/operator maintenance is the responsibility of the owner/operator.

Your water supply must be within these general guidelines:

DYNAMIC WATER PRESSURE	30-60 psig
HARDNESS *	less than 3 grains
SILICA	less than 13 ppm
TOTAL CHLORIDE	less than 30 ppm
Ph RANGE	7-8
CHLORINE & CHLORAMINE	0 ppm
ALKALINITY	less than 20 ppm
TDS	less than 60 ppm
UN-DISSOLVED SOLIDS	less than 5 microns
* 17.1 ppm = 1 grain of hardness

Other factors affecting steam generation are iron content, amount of chlorination and dissolved gasses. Water supplies vary from state to state and from locations within a state. Therefore it is necessary that the local water treatment specialist be consulted before the installation of any steam generating equipment.

Note:

•Installation of backflow preventers, vacuum breakers and other specific code requirements is the responsibility of the owner and installer in compliance with local codes.

•Plastic drains are not recommended due to inherent limited temperatures of the plastic. The installer may be required to provide means to reduce water drain temperature to be that of the condensate temperature of 140°F or less.

As continued product improvement is a policy of Hobart, specifications are subject to change without notice.

Page 2 of 2	F-40269 – CG10FI Gas Full Size Combi Oven
F-40269 (REV. 06/11)	LITHO IN U.S.A. (H-01)

CG10FI specifications

The Hobart CG10FI is a standout model in the realm of commercial cooking equipment, engineered for efficiency and performance in high-demand kitchen environments. This countertop gas fryer is designed to meet the needs of restaurants, cafes, and catering operations looking for reliability and high output in a compact format.

One of the main features of the Hobart CG10FI is its impressive fry capacity. The unit can accommodate up to 10 pounds of oil, making it suitable for frying a variety of foods, from crispy French fries to battered chicken. With a powerful gas burner system, it heats oil quickly, ensuring short wait times for busy kitchen staff and quick service for patrons.

The fryer is equipped with a temperature control feature that allows operators to set and maintain precise frying temperatures. This is crucial for achieving consistent results and reducing food waste. The built-in thermostat provides accurate readings, while an easy-to-read digital display offers added convenience in monitoring the cooking process.

Another notable characteristic of the Hobart CG10FI is its user-friendly design. The fryer features a hinged stainless steel lid, making it easy to access the frying basket and oil for quick refills or cleaning. The removable oil tank simplifies maintenance by allowing for easy draining and cleaning, promoting hygiene and longevity.

Safety is a top priority in the Hobart CG10FI design. The fryer includes a flame failure safety device, which automatically shuts off the gas supply in case of a flameout. Additionally, its robust construction ensures durability, even in the most bustling kitchen environments.

The fryer also boasts an impressive energy efficiency profile. Designed with advanced burner technology, it effectively utilizes gas while minimizing heat loss, which can lead to cost savings over time. The unit’s compact footprint makes it an ideal choice for kitchens with limited space without compromising on performance.

In summary, the Hobart CG10FI combines high capacity, precise temperature control, safety features, and user-friendly design. It stands out in the commercial kitchen equipment market, catering to the demanding needs of food service professionals. With these features, the CG10FI not only enhances culinary capabilities but also ensures operational efficiency and safety. Whether frying appetizers, sides, or mains, this fryer is built to deliver exceptional results time and again.