Microcomputer Control System Hobart | Hobart AM15VLF specification

701 S Ridge Avenue, Troy, OH 45374

1-888-4HOBART • www.hobartcorp.com

VENTLESS FRONT LOADING DISHWASHER

The microcomputer-based control system is built into the AM Select Ventless dishwasher. It is available in standard electrical specifications of 208-240/60/1, 208-240/60/3, 480/60/3 and is equipped with a reduced voltage pilot circuit transformer.

Water hardness must be controlled to 3 grains of hardness or less for best results.

CONSTRUCTION: Drawn tank, tank shelf and feet constructed of 16 gauge stainless steel. Wash cham- ber and front trim panel above motor compartment are polished, satin finish. Frame is 12 gauge stainless steel, chamber is 18 gauge, and removable trim pan- els are 20 gauge.

CHAMBER: Stainless steel chamber with large

203⁄4" W x 27" H opening will accommodate 18" x 26" sheet pans or a 60-quart mixing bowl.

CHAMBER LIFT: Chamber coupled by stainless steel handle, spring counterbalanced. Chamber guided for ease of operation and long life.

WASH PUMP: With stainless steel pump and impeller, integral with motor assures alignment and quiet oper- ation. Pump shaft seal with stainless steel parts and a carbon ceramic sealing interface. Easily removable impeller housing permits ease of inspection. Capacity 160 GPM. Pump is completely self-draining.

WASH PUMP MOTOR: Built for Hobart, 2 H.P., with inherent thermal protection, grease-packed ball bear- ings, splash-proof design, ventilated. Single-phase is capacitor-start, induction-run type. Three-phase is squirrel-cage, induction type.

RINSE PUMP: Powered by a 1⁄15 H.P. single phase motor, the rinse pump is made of high strength engi- neered composite material.

BLOWER: The condenser blower is an all stainless steel forward curved centrifugal wheel powered by a 1⁄20 H.P. TEFC single phase motor for nearly silent operation.

CONDENSER COIL: The condensing system using a tube and fin coil constructed of copper and corrosion resistant aluminum.

MICROCOMPUTER CONTROL SYSTEM: Hobart

microcomputercontrols, assembled within water- resistant enclosure, provide built-in performance and reliability.

The microcomputer control, relays and contactors are housed behind a stainless steel enclosure, hinged

to provide easy access for servicing. The line volt- age electrical components are completely wired with 105°C, 600V thermoplastic insulated wire with stranded conductors. Electrical components are wired with type ST cord. Line disconnect switch NOT furnished.

CYCLE OPERATION: The microcomputer-timing program is started by closing the doors, which actu- ates the door cycle switch. The cycle light turns ON. The microcomputer energizes the wash pump motor contactor during the wash portion of the program. After the wash, a dwell permits the upper wash mani- fold to drain. At the end of the dwell, the final rinse pump is energized. After the final rinse pump turns off, Sani-Dwell permits sanitization to continue. The Rinse display remains on during this period. The Blower and Cold Water Valve turn on for 30 seconds to condense the vapor laden air inside of the chamber. The display shows a count down time (in seconds) during this operation. After the 30 seconds is complete the Cycle Light turns OFF, completing the program. If the microcomputer is interrupted during a cycle by the door-cycle switch, the microcomputer is reset to the beginning of the program. 40 racks per hour – 87 sec- onds: 38 Second Wash, 2 Second Dwell, 10 Second Rinse, 7 Second Sani-Dwell. 30 Second Condensing. Other programs can be pre-selected by your Hobart service technician.

Manual wash cycle selector also provides selection of 2-, 4- or 6-minute wash cycles plus condense time for heavier washing applications.

WASH: Hobart revolving stainless steel wash arms with unrestricted openings above and below provide thorough distribution of water jets to all dishware surfaces. Arms are easily removable for cleaning and are interchangeable. Stainless steel tubing manifold connects upper and lower spray system.

RINSE: Rotating rinse arms, both upper and lower, feature 14 rinse nozzles. The stainless steel upper and lower rinse arms are easily removable without tools for inspection and are interchangeable. The motor driven rinse pump gives constant rinse pressure regardless of water service supply pressure. Easy open brass line strainer furnished.

HOT FILL: Microcomputer controlled fill is supplied from the hot water service connection. It enters the machine through an air gap system which protects the potable water supply from contamination. Ratio fill method is used giving the correct fill at any flowing water pressure.

F-40273 –

Ventless Front Loading Dishwasher

Page 7 of 8

AM15VLF specifications

The Hobart AM15VLF is a state-of-the-art commercial dishwashing machine that epitomizes efficiency and reliability in the foodservice industry. Designed to meet the rigorous demands of high-volume kitchens, this machine offers a blend of advanced technology and user-friendly features that facilitate superior cleaning performance.

One of the standout features of the AM15VLF is its impressive capacity. It is capable of washing up to 30 racks per hour, making it an ideal choice for busy restaurants and catering operations. The machine is designed to handle a wide variety of dishware, including plates, glasses, and utensils, ensuring that all items are sanitized and ready for service in a minimal amount of time.

The AM15VLF employs a powerful yet energy-efficient wash system. This includes a powerful pump and spray arms that deliver a thorough wash while minimizing water consumption. With its low-flow technology, the dishwasher can operate using less water than traditional models, leading to significant savings on utility costs over time. The energy-saving mode further enhances efficiency, allowing the machine to reduce energy consumption during low-demand periods.

User convenience is a primary focus in the design of the AM15VLF. The machine features a digital control panel that allows operators to select wash cycles with ease. Additionally, the built-in automatic chemical dispensers ensure that the right amount of detergent is used for each cycle, resulting in consistently clean dishes without the risk of overuse or waste.

Durability is another key characteristic of the AM15VLF. Constructed with high-quality stainless steel, the machine is built to withstand the rigors of a commercial kitchen environment. The hygienic design also minimizes the risk of cross-contamination, making it an ideal choice for establishments that prioritize food safety.

The Hobart AM15VLF also incorporates advanced technologies such as a self-diagnostic system. This feature allows for easy troubleshooting, enabling operators to quickly identify and address any issues that may arise during operation, thus minimizing downtime.

In summary, the Hobart AM15VLF is a powerful, efficient, and user-friendly commercial dishwasher that is well-suited for high-demand foodservice operations. With its impressive cleaning capacity, advanced wash system, and durable construction, it serves as a reliable partner for any kitchen, ensuring that dishwashing is efficient and effective.