Cleaning, Service Procedures, Introduction | Frymaster MSDU specification

2.4 Cleaning

Clean the crumb screen with a solution of detergent and water. Clean the exterior surfaces of the MSDU with a soft cloth and a solution of detergent and water. It is not necessary to clean the interior of the reservoir, but if desired it may be wiped down with clean paper towels to remove excess residual oil.

WARNING

DO NOT clean the interior of the reservoir with water or detergent. Introduction of water or detergent into the unit will permanently damage the pump.

3.SERVICE PROCEDURES

3.1 Introduction

Other than routine cleaning and the replacement of worn suction tube O-rings, the MSDU is maintenance free. After long use, the pump vanes and pump shaft seal may require replacement due to wear. Frymaster recommends worn pump vanes and/or pump shaft seals be replaced by an FASC, but store personnel may perform these service actions without voiding the warranty.

3.2 Replacing Worn or Damaged O-Rings

If pump efficiency degrades, it is likely that the O-rings on the suction tube are worn or damaged. To replace the O-rings, follow the steps below.

1.Lift the pump assembly straight up and out of the handle assembly.

2.Remove the worn or damaged O-rings from the grooves at the bottom of the suction tube and replace with new O-rings. Apply Accrolube with Teflon grease or equivalent to bottom 2 inches of the suction tube.

3.Insert the suction tube through the tube bracket in the handle and into the receiver on top of the reservoir. Push down on the pump assembly to make sure the suction tube is fully seated.

3.3 Replacing Worn Pump Vanes and/or Pump Shaft Seal

Depending upon the amount of use, the vanes in the pump assembly will eventually wear, reducing the efficiency of the pump. The pump shaft seal can also become worn and start to leak. A kit for replacing the vanes and the seal is available. The pump shaft seal can also be purchased as a separate item. To replace the pump vanes, and/or the pump shaft seal, follow the steps below (refer also to the illustration on Page 6).

1.Loosen the setscrew securing the pump handle to the pump shaft and slip the handle off the shaft.

2.Remove the five screws securing the front cover and remove the cover.

If replacing the pump shaft seal only, remove the old seal and install the replacement as shown in the illustration on Page 6, then go to Step 5.

If replacing the pump vanes, go to Step 3.

MSDU specifications

The Frymaster MSDU, or Multi-Service Fryer, is a versatile and innovative cooking solution designed for commercial kitchens. Renowned for its efficiency and ability to handle high-volume frying tasks, the MSDU combines advanced technologies with user-friendly features, making it a popular choice among chefs and restaurant owners.

One of the standout characteristics of the Frymaster MSDU is its multi-basket capability. This feature allows operators to cook multiple batches of different foods simultaneously, significantly increasing productivity. With independent temperature controls for each basket, chefs can ensure that each type of food is cooked to perfection without any risk of flavor transfer or cross-contamination.

The MSDU also boasts energy-efficient operation, which is a critical consideration for modern kitchens. Utilizing patented technologies, this fryer optimizes energy consumption while maintaining performance. The built-in, high-efficiency burners deliver rapid heat-up times, reducing wait time between frying cycles. This not only enhances productivity but also supports cost savings on energy bills, making it a financially savvy investment for businesses.

In terms of temperature management, the Frymaster MSDU features advanced controls that ensure precise temperature regulation. The intelligent oil filtration system aids in maintaining the quality of the cooking oil, extending its life, and contributing to better-tasting food. By filtering out food particles and contaminants automatically, the MSDU promotes health and safety standards in food preparation while minimizing manual labor for kitchen staff.

The design of the MSDU also emphasizes ease of use and maintenance. With a user-friendly digital interface, chefs can easily adjust settings, monitor cooking times, and access maintenance notifications. The fryer is constructed from durable stainless steel, ensuring it can withstand the rigors of a busy kitchen environment. Its sleek design allows for easy cleaning, further enhancing its functionality.

Safety is another crucial aspect of the Frymaster MSDU. With advanced safety features including automatic shut-off systems and cool-to-the-touch exteriors, this fryer mitigates potential kitchen hazards. It also incorporates built-in alarms and indicators, keeping operators informed during frying cycles.

In conclusion, the Frymaster MSDU is a state-of-the-art frying solution that combines efficiency, safety, and ease of use. Its multi-basket design, energy-saving technology, and focus on safety and maintenance make it an excellent choice for restaurants that demand high performance from their kitchen equipment. As the food service industry continues to evolve, the Frymaster MSDU stands out as a reliable ally for chefs dedicated to delivering quality fried foods.