Jenn-Air JMW8.530, JJW8630, JJW8627 Ovenwindow, Faultcodes, Window, Feuds ~0 not Broil Properly

OVEN LIGHT

Before replacing light bulb, DISCONNECT POWER TO OVEN. Be sure bulb is cool. Do not touch a hot bulb with a damp cloth as the bulb may break.

TO REPLACE OVEN LIGHT:

Use a dry potholder and very carefully un- screw bulb cover and bulb. Replace with a 40 watt, oven-rated appliance bulb. Bulb with a

brass base is recommended to preventfusing

Of bulb into socket*

Replace bulb cover and reconnect power to oven. Reset clock.

OVENWINDOW

TO PROTECT THE OVEN DOOR

WINDOW .

I.Do not use abrasive cleaning agents such

as steel wool scouring pads or powdered cleansers as they may scratch the glass.

2.Do not hit the glass with pots, pans, furniture, toys, or other objects.

3.Do not close the oven door until the oven racks are in place.

Scratching, hitting, jarring or stressing the glass may weaken its structure causing an increased risk of breakage at a later date.

2?EFORE You CALL FORSERVICE

FORMOSTCONCERNS,TRYTHESEFIRST:l Excessive spills were not removed prior to self-

l	Check if oven controls are properly		set.	cleaning process.
l	Check if oven is properly	connected	to electri- b	FEUDS ~0 NOT BROIL PROPERLY:
	cal outlet.		l	Check rack position. (See page 5.)
l	Check or re-set circuit	breaker. Check or		Voltage into house may be low.
	replace fuse.		l
			~BAKEDFOODISBURNEDORTOO
l	Check power SUDD~Y.
IF CLOCK,INDICATORWORDS,AND/OR BRoWNoNToP:
LIGHTSOPERATEBUTOVENDOESNOT l				Food may be positioned incorrectly in oven.
HEAT:				(See“CookingMade Simple” booklet.)

l Oven not preheated properly.

. Clock controls may be set for a delayed bake

l Oven thermostat calibration may differ be- tween old and new ovens. Follow recipe and use the directions in this guide before calling for service since the calibration on the previous oven may have drifted to a too high or too low setting. (See p. 4 - Adjusting Oven Tempera- ture.)

~THECOOLINGFANCONTINUESTO OPERATEAFTERTHEOVENHASBEEN TURNEDOFF:

lThis is normal. The fan will automatically shut off when the oven is cooled.

IFAFANISHEARDWHILEUSINGTHE BROILAND CLEANMODES:

function.

. The Oven Control Lockout may have been set. (See page 4.)

IFTHE OVENLIGHTAND/ORCLOCK DOESNOTFUNCTION:

lThe light bulb is loose or defective.

l The oven light does not work during self-

cleaning process.

-

bFOODSBAKEUNEVENLY:

lThe oven may be installed improperly.

lCheck the oven rack with a level.

lStagger pans, do not allow pans to touch each other or oven wall.

lCheck instructions for suggested placement of pans on oven rack. (See “Cooking Made Simple” booklet.)

lThis is the cooling fan and is normal. The fan will continue to run after use until the oven cools.

FAULTCODES

l Fault codes are shown in the display as “F”and

a number. If a fault code appears in the display

and beeps sound, press the Cancel pad. If the

fault code and beeps continue after pressing

Cancel, disconnect power to the oven. Wait a

THEREISASTRONGODORORLIGHT SMOKEWHENOVENISTURNEDON:

lThis is normal for a new wall oven and will disappear after afew uses.Initiating a clean cycle will “burnoff’the smells more quickly. Turning on a ventilation fan will help remove the smoke and/or odor.

. Excessive food soils on the oven bottom. Use a self-clean cycle.

IF OVENWILLNOTACTIVATETHESELF- CLEANINGPROCESS:

lCheck the “Clean”and “Stop”time settings and the current time of day on the clock.

lOven may not have cooled to safetemperature after self-cleaning process.

IFOVENBAKINGRESULTSARELESS THANEXPECTED:

lThe pans being used may not be of the size or material recommended for best results. (See

“CookingMade Simple” booklet).

lThere may not be sufficient room around sides of the pans for proper air circulation in the oven.

lCheck instructions for preheating, rack posi- tion and oven temoerature.

few minutes, then reconnect power to the oven.

If the fault code and beeps still continue, discon-

nect power to the wall oven and call an autho-

rized servicer.

lIf the oven is heavily soiled, excessive flare-ups may result in a fault code during a clean cycle. Press Cancel pad and allowthe oven to cool for one hour, then reset the clean cycle. If the fault code and beeps still continue, disconnect power to the appliance and call an authorized servicer.

l If an error beep sounds (two short beeps) with

no fault code in the display, clean any spill from

key pad area within 30 seconds. If, after 30

seconds the spill is not removed or another

problem exists, an F7 fault code will be dis-

IFOVENDIDNOTCLEANPROPERLY: IFBAKINGRESULTSDIFFERFROM PREVIOUSOVEN:

l Oven may need longer cleaning time.

played. Disconnect power to the appliance and

call an authorized servicer.

IO